Thanks ^^
Btw, can you tell me how to read the temp from the ESC ?
Last night, after a few laps, I have tried following the instruction manual to temp the ESC and motor and it showed only 1 flash at a time. Referring to the manual, is it mean that it is around 45 DC (not sure the -ve sign means).
When I have touched the ESC and motor, they are cool. Please advise.作者: billlkyy 時間: 2010-11-19 19:33 回復 7#mikuro
45 or more ，I just buy hobbywing 1s esc without program card but can't set other mode on the set button，anyone know ?作者: mikuro 時間: 2010-11-19 21:07 回復 8#billlkyy
How much is it?作者: billlkyy 時間: 2010-11-19 21:14
$820!!!!作者: winclearly 時間: 2010-12-19 14:38
Seems you can try a lower gear ratio, e.g 24/96 ^^
Btw, did you check with the gear ratio that most Ching set when playing at TRC?作者: winclearly 時間: 2010-12-19 19:17
ching,我下次試試,thx作者: wingscreamer 時間: 2010-12-27 11:14
SXX Ver2, 請問你們點樣set mode? yellow/ red/ both yellow and red?
any different?作者: mikuro 時間: 2010-12-27 17:50 本帖最後由 mikuro 於 2010-12-27 18:00 編輯
Press the "mode" button for at least 3 second until it starts to flash.
For mode 1, if you are using 1-cell lipo, the setting is #1 so you have press the "set" button only 1 blue light flash only in mode 1. If you are using 2-cell lipo, the setting is #2 so that you have to press the "set" botton 1 more time and there should be 2 blue light flash in mode 1, vice and versa.
When you finished setting in mode 1, press "mode" button again to change to mode 2.
Taking an example, if you want to set the throttle feel to linear, ie. #7, you have to press the "set" button several times until there are 7 blue flashes. Once finished, press "set" button again and then switch to mode 3.
Make sure you have to press the "set" button after mode 4, there will be only 1 solid blue light in the "mode" light which means setting mode finished. ^^
For further details, please refer to the SXX ver2 manual.作者: wingscreamer 時間: 2010-12-27 18:40
Thanks for your kind help ching, let me trytry!作者: mikuro 時間: 2010-12-27 18:48 回復 18#wingscreamer
Unlike HW / SP ESC that they are more user-friendly since it can be easily done by using the setting card, luckily the SXX v2 only got 4 modes. ^^作者: wingscreamer 時間: 2010-12-27 23:56
Thanks all Ching, I did it but my Sxx mode setting is mode 2 at #7 and mode 3 at #5,
will it be easy to burn or damage? please help to advise..!作者: mikuro 時間: 2010-12-28 09:34 本帖最後由 mikuro 於 2010-12-28 13:31 編輯
I have referred to previous comment by Ching here that you better check the temperature of both ESC and Motor after few laps, which is better if they are around 60 DC.
I think 4.0T is very fast, therefore, you should try using low boost value in mode 3, say #2 or #3. Check temperatures again.
If you feel the speed is low, try re-gearing first and if you still find it is slow then set higher boost in your ESC.
But of course, it would depends on what kind of tracks, ie. more long straight or more cornering. See which setting make you feel better driving with your 1/12 pan car. I am still learning from that ^^作者: wingscreamer 時間: 2010-12-28 12:22
Oic Thanks mikuro Ching!
