加入truggy 行列

小弟最終係buggy，rally同truggy之間揀咗truggy,不過未買齊嘢

已完成，爭servo未裝

師兄所提示之OP已買了

The CVD part... Very true...  Esp the rear one....

I still wonder why 1/8 don't use '二樓版' as 1/10 ... Even a small narrow carbon or alloy.. On nitro, may be hard, but on electric, should be fine to locate....

The CVD part... Very true...  Esp the rear one....

I still wonder why 1/8 don't use '二樓版' as 1/10 ... Even a small narrow carbon or alloy.. On nitro, may be hard, but on electric, should be fine to locate....

咁好似換咗先好啲喎

965 發表於 2013-11-15 10:49
I wonder how much is it in HK?

Does the Truggy version come in RTR?

無錯，膠撐好平，斷左都唔肉痛，但佢太軟的關係，唔夠力撐，果份衝力就去左CVD，輕則彎，重則斷。

thx all ching, but i saw all of the buggy and truggy use metal chassis

You can actually run 5s, I like 5s a lots, (if you use 1800kv) especially for the T8, the motor side is heavier then the other side, so you can run 3s on one side, 2s on the motor side, to balance it off.

Let's say 4000 mah, 3s is app 350g .. 2s is 250g ...  

I wonder how much is it in HK?

Does the Truggy version come in RTR?

I actually like the idea of "plastic" chassis brace, worst case, that piece of plastic break, may be $20HKD or so ...  but with big strong Metal chassis brace, you may bend the chassis, break the arms/tower/ etc before the brace ...  

It really depends how you play, for track/race, you want a very stiff chassis, for bashing/jump high, you want a bit flexibility ..

Somehow, my Truggies with alloy brace, (Serpent/Hpi/Losi/Mugen etc .. ) all result with broken arm/mount/hub/tower etc ...

Actually, with "turnbuckle" is the best, probably just pop out under big jump/hit!

(something like this http://www.pmhobbycraft.ca/RC8-CHASSIS-BRACE-SET-REAR-ASC89069/)

4S 無咁猛, 你先去了解架車既特性, 熟左先買6S

slowerthanyou 發表於 2013-11-14 17:34
hey there, so you got a tuggy in the end? Nice. Looks like a lot of fun

suggestion for batteries/mo ...

咁我買咗hobbywing 150a 1800 kv用6s定4s 好呢？

hey there, so you got a tuggy in the end? Nice. Looks like a lot of fun

suggestion for batteries/motor combo

4s 1900-2100KV
6s 1400-1700KV

咁一早換咗佢定爛咗先換好呢？呔選擇咩好呀請問

piranharowana 發表於 2013-11-14 13:40
咁聽師兄咁講真係要換喎，嗰個chassis  protection plate都係要金屬？本身servo horm同saver係咩嚟？唔好意 ...

Plate 係金屬，保護底版尾波箱位置。
金屬servo saver and horn，原裝係膠的，無咁受力。

登錄/註冊後可看大圖

咁聽師兄咁講真係要換喎，嗰個chassis  protection plate都係要金屬？本身servo horm同saver係咩嚟？唔好意思呀，小弟初玩太多問題

piranharowana 發表於 2013-11-14 11:45
哦，是嗎？謝謝你啊，但原裝係咪一撞就會報銷？

原裝是膠的，膠太軟，但支CVD 會食晒...。
其實仲有樣，不過唔肯定是否o岩 truggy, 係 TU0817 Chassis Protection Plate
另外Servo saver and Servo Horn 最好用埋金屬，咁就正常。

6s?會唔會頂唔順？