TA02 改 Mini Rally

差唔多完成,Size同ABC架一樣,差二樓板,直軸,做埋防水工程,攪埋今晚,就可以試車....

[ 本帖最後由 bcgg 於 2007-10-4 14:16 編輯 ]

jjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjj

[ 本帖最後由 bcgg 於 2007-10-4 14:16 編輯 ]

勁!

勁!

Thanks
冇辨法,我冇M size 車,但好想玩 Mini Rally,唯有咁做

完全用舊野堆砌,冇買新野,慳到錢又有新車玩(新感覺)

The 'silver' gearbox if my memory is not wrong, is only produced for Porsche 911 GT2... and is
kind of unique.

good job man !

The 'silver' gearbox if my memory is not wrong, is only produced for Porsche 911 GT2... and is
kind of unique.

You are right
And I have the black version too

good job man !

Thanks
等侍同你架Mini惡鬥一番

nice design in the rear adjustable toe-in....wooooo!!!!!

原帖由 bcgg 於 2006-6-22 10:02 發表


Thanks
等侍同你架Mini惡鬥一番

一定你個架好跑啦 ! 又 4wd , 我地 d 頭輪都係行埋一邊啦 !

等我又整返架TA01先....想問下D狗骨係邊度走出黎?? M車買剩狗骨係無,要買萬向.....

剛剛發現你個尾杯係前轉向杯黎????

nice design in the rear adjustable toe-in....wooooo!!!!!

Thanks a lots!
參考ABC mini的, 現正研究如何發展4WD+4WS的可能性

等我又整返架TA01先....想問下D狗骨係邊度走出黎?? M車買剩狗骨係無,要買萬向.....

Panther兄:

給你小小資料參考:
頭尾臂為TL01前面嗰種最短的臂,
頭尾轉向為TA02/03嗰隻轉向杯,
狗骨為TA02前狗骨,但狗骨連接轉向杯那面的頭,食落去兩邊
轉向杯一字位,每邊打磨由3mm至2mm(大約),因TA02/03嗰隻轉向杯
裡面行大bearing,TA02前狗骨係入唔到,要打磨才可以(你用支TA03狗骨同
TA02狗骨比較就知道)
而原本後面唔係咁整,但用原本TA02嗰art做,會短左,冇狗骨入到,望下望下
架ABC,就係咁啓發左出嚟....
後油壓板係TB EVO後面嗰塊,
整完玩下先,睇下有冇換金屬Parts需要...
而底板,電位,我唸你係大師兄,唔駛我講啦
祝TA01改造順利,期侍

一定你個架好跑啦 ! 又 4wd , 我地 d 頭輪都係行埋一邊啦 !  

又唔一定喎...我有架FF01,入埋電攞上手都係好輕,而我架4WD一定重過晒D頭輪車,
又食電,再加上你係大窩口D豐富實戰經驗,隨時Vtech跑贏Evolution啦

絛中軸點攪?

我都有架TA-02,唔洗$

整完之後上咗神枱~

我又想改

絛中軸點攪?

我都有架TA-02,唔洗$

整完之後上咗神枱~

我又想改  

絛中軸.....都係Cut短,打磨軸頭...(Photo Later)

快D改下玩下啦有問題大家研究下

原帖由 bcgg 於 2006-6-22 11:20 發表



絛中軸.....都係Cut短,打磨軸頭...(Photo Later)

快D改下玩下啦有問題大家研究下

Cut短??

點CUT法?

好利害呀.我都想整返架玩吓.但係架車要闊170mmオ要正宗m車.