My Pan car ^^

Hi, as mentioned at #117 or you can see details as follows. Roll-out is about 41mm/rev ^^

Tod ...
mikuro 發表於 2011-2-1 15:12

                               
登錄/註冊後可看大圖

Thx for the info, Ur front tires dia seems fine but rear deemed a bit thicker than it should be. May I know which roll center blocks u r using ? Any spin out ?  Wondering whether u hv overgeared alittle, hv u measure the temp of both Esc and motor? What is the actual laptime of Ur 24/96 on 4.0, any pit stop ? And Ur mapped time also counted them in?

No offense, just want to learn how to gain extra run time for my 1/12, sincerely hope that u can share Ur expertise with us

Normally for playing at asphalt like JV, I will set the ride height about 4.5-4.8mm, both front and rear.
Also, I will use tire addictive, full on rear, outer half on front. No spinning issue by far.
Have tested on the first few times that the temp. on both ESC and motor is about 40-45DC. It is not high. Now, I only temp them by hand after play ^_^. Checked by myself and other Ching, the temp is not high.
Yes, I will drive via pit shop like touch and go and only some occasion, will stop for 1-2 times within 10s (will get tired since we can't play like robot ^_^). But this have been deducted from the total play time.
So, this run times is for reference only and it would be varies from different players.

Hi, as mentioned at #117 or you can see details as follows. Roll-out is about 41mm/rev ^^

Tod ...
mikuro 發表於 2011-2-1 15:12

                               
登錄/註冊後可看大圖

Mikuro ching,

4.0t 24/96 dia 52mm  = rollout 40.84?

Mikuro ching,

4.0t 24/96 dia 52mm  = rollout 40.84?
QSO 發表於 2011-2-1 23:41

                               
登錄/註冊後可看大圖

Hello, could you please be more specify on the question? Thanks ^^

回復 140# mikuro

mikuro兄

我係想問是不是隻4.ot 摩打可以行到齒比 rollout 40呢?

謝謝

回復  mikuro

mikuro兄

我係想問是不是隻4.ot 摩打可以行到齒比 rollout 40呢?

謝謝
QSO 發表於 2011-2-2 00:11

                               
登錄/註冊後可看大圖

Hi Qso 兄

I follow the roll-out calculation as follows:

52mm x 3.1416 x 24 / 96 = 40.84mm per revolution

In theory, with the same roll-out of 2 cars, the higher the revolution of a motor, the more the forward distance of the car. ^^

Mikuro 兄

40.84 rollout 會否過高?

thx

Mikuro 兄

40.84 rollout 會否過高?

thx
QSO 發表於 2011-2-2 01:27

                               
登錄/註冊後可看大圖

    Yes, according to the technical spec, the recommend rollout for 1/12 car when using 4.0T would be smaller than 29mm/rec.
    But, in a large and high-speed asphalt track like JV, it is okay.

Hello all
Some update on my CRC Gen X10 LE + 235mm kit ^^

嘩！溜口水！己加至235mm？用咩彀？

嘩！溜口水！己加至235mm？用咩彀？
hairy 發表於 2011-2-7 18:40

                               
登錄/註冊後可看大圖

Hairy 兄, 會用 Protoform P905B ^^
今日JV 都有幾架 12仔, 我仲同另外一個 3S 師兄玩, 好正 !

回復 149# mikuro

毒到爆!!!!

我都想玩pro10

我都想玩pro10
billlkyy 發表於 2011-2-7 19:27

                               
登錄/註冊後可看大圖

    多d人玩會開心d, gogogo ^^

太毒，套Kit 3XX ，太正。

太毒，套Kit 3XX ，太正。
pd 發表於 2011-2-7 19:38

                               
登錄/註冊後可看大圖

    Thanks pd 兄, 如果 Xray 套 235mm kit 好似 CRC 咁就好 lu >_<

Xray = Rolex
Btw, how's your CRC , good running?

Xray = Rolex
Btw, how's your CRC , good running?
pd 發表於 2011-2-7 20:07

                               
登錄/註冊後可看大圖

My one is not completed yet. I may try testing my X10_LE by using the ESC and motor from my 12 son.
How about your 1/10 pan car?

回復 154# mikuro


    我星期六來唔到呢

回復 158# mikuro


    Use 3.7 lipo?