RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

標題: Yokomo 180SX 彈燈 Trust 花 [打印本頁]

作者: DriftNoobie    時間: 2008-11-9 10:05
標題: Yokomo 180SX 彈燈 Trust 花
好耐無整殼, 湊仔期間偷時間整左呢隻野...

Yokomo 180SX 殼
Yokomo S15 Trust 花
3Racing 燈 + 後鏡指揮燈
DIY 前後燈杯  
DIY 彈燈 (用 3rd channel 控制)
Yokomo 發光死氣喉
Yokomo Volks 車轆
HPI Toyo Drift 呔


                               
登錄/註冊後可看大圖


Click 圖睇彈燈片 (要等片 loading)

                               
登錄/註冊後可看大圖


[ 本帖最後由 DriftNoobie 於 2008-11-9 10:07 編輯 ]
作者: orangeteam    時間: 2008-11-9 10:23
一個字 "靚"
作者: kachunsky    時間: 2008-11-9 10:36
好靚喔~!
作者: gegegum    時間: 2008-11-9 10:56
好耐都冇見你o既作品, 果然有驚喜!
作者: lunb    時間: 2008-11-9 11:28
如果係我就唔捨得俾佢落地行
作者: gegegum    時間: 2008-11-9 11:49
原帖由 lunb 於 2008-11-9 11:28 AM 發表
如果係我就唔捨得俾佢落地行

只要落過一次, 就唔會唔捨得!
作者: jm144    時間: 2008-11-9 12:50
feel so good`
作者: DriftNoobie    時間: 2008-11-9 12:50
原帖由 gegegum 於 2008-11-9 10:56 發表
好耐都冇見你o既作品, 果然有驚喜!


真係好耐, 要揍住個仔, 所以無哂時間玩車...

Thank you.
作者: SPAWN    時間: 2008-11-9 12:55
靚得我想哭
作者: gegegum    時間: 2008-11-9 13:15
係喎! 唔記得問盞燈可唔可能開一半架!?
作者: DriftNoobie    時間: 2008-11-9 14:41
原帖由 gegegum 於 2008-11-9 13:15 發表
係喎! 唔記得問盞燈可唔可能開一半架!?


No ah, full open or full shut
作者: 黑夜番長    時間: 2008-11-9 14:57
好正呀~~~~師兄
作者: DriftNoobie    時間: 2008-11-9 16:04
原帖由 lunb 於 2008-11-9 11:28 發表
如果係我就唔捨得俾佢落地行


我估... 佢都有排無咩機會落地, 我要揍仔.
作者: gegegum    時間: 2008-11-9 17:08
原帖由 DriftNoobie 於 2008-11-9 04:04 PM 發表


我估... 佢都有排無咩機會落地, 我要揍仔.

我都要揍女啦!
作者: DriftNoobie    時間: 2008-11-9 17:31
原帖由 gegegum 於 2008-11-9 17:08 發表

我都要揍女啦!


我隻百厭星兩個月大, 自己揍 (唔想佢學菲律賓話), 勁攞命.

你個寶貝女幾歲?
作者: monkichi0210    時間: 2008-11-9 20:15
原帖由 DriftNoobie 於 2008-11-9 10:05 發表
好耐無整殼, 湊仔期間偷時間整左呢隻野...

Yokomo 180SX 殼
Yokomo S15 Trust 花
3Racing 燈 + 後鏡指揮燈
DIY 前後燈杯  
DIY 彈燈 (用 3rd channel 控制)
Yokomo 發光死氣喉
Yokomo Volks 車轆
HPI Toy ...


sooooooooo gooooood!!!!
可否睇下跳燈點整呢!!!????
作者: DriftNoobie    時間: 2008-11-9 20:29
Inside photo later.

I used a Futaba Helicopter servo S3156. It is a slow but high torque servo, which I think the movement speed is quite realistic.

The pop-up light buckets came with the shell. But modifications are needed for both the bucket and the shell body itself.

It is very simple:
(1) I made a "[" shape rod. Attach light buckets at each end.

(2) The micro servo is place at center with double faced tape + duck tape.

(3) The servo arm is attached to the rod directly with an "8" shape wire.
(Note: Don't tie too tight for allowing some free movement or the servo may rip the light buckets off from the shell)

(4) Connect the servo to Rx with an extension cord.

(5) The lights is now connected to the 3Racing unit which turns on when the car runs forward. However, I will separate that to let it turn on by itself. Simply add a button on the shell near the servo arm tip, so the light will turn on when the bucket is up (servo up and touching the button) all the way (looks realistic) and turn off before the bucket goes down.

That's all. The hardest part is modifying the light buckets and body.

[ 本帖最後由 DriftNoobie 於 2008-11-9 20:31 編輯 ]
作者: gegegum    時間: 2008-11-11 02:50
原帖由 DriftNoobie 於 2008-11-9 08:29 PM 發表
Inside photo later.

I used a Futaba Helicopter servo S3156. It is a slow but high torque servo, which I think the movement speed is quite realistic.

The pop-up light buckets came with the shel ...

成份manual咁!
作者: Vinz    時間: 2008-11-11 10:56
Very Nice with sharp color matching
作者: paulyfrankietam    時間: 2008-11-11 11:14
WOW so good on 180SX !!!!!!!!so Good ar!!!!!!!!!!!!! :
作者: tungming508    時間: 2008-11-11 12:12
好靚~最愛Trust!不過經營不善巳經......
作者: DriftNoobie    時間: 2008-11-11 16:26
原帖由 tungming508 於 2008-11-11 12:12 發表
好靚~最愛Trust!不過經營不善巳經......


絕版, 所以特別有炒賣價值.
作者: 12wai3    時間: 2008-11-11 16:40
師兄既彈燈同 Trust花 真係勁正. 好有心機
作者: blackcolt    時間: 2008-11-11 17:16
好靚 ~~
作者: Cepacol    時間: 2009-5-17 20:05
好帥的 180SX!

最重要是你願意分享制造分法, 獲益良多.
很多人都很自私, 不會分享好東西.  

謝謝


作者: KIT25    時間: 2009-5-18 00:31
very good....
作者: ANODIZE    時間: 2009-5-18 01:29
彈燈做得好正
作者: DriftNoobie    時間: 2009-5-18 13:07
嘩, 沈左咁耐既 post 都比人搵番出黎.

Thank you.  
作者: Diner    時間: 2009-5-18 20:58
靚!!
作者: muken    時間: 2009-5-22 00:00
好正呀!!!!!!!
作者: tongto1    時間: 2009-5-25 12:09
型囉....................




歡迎光臨 RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區 (https://rc-evo.com/xbbs/) Powered by Discuz! X3.2