RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

標題: GTB Problem [打印本頁]

作者: Ivan 時間: 2006-5-30 15:38
標題: GTB Problem
My GTB 5.5 run like a 540. I don't know why, I confirm everything is correct, including the gear ratio. Any bro can help me? Thanks

作者: Timothypychan 時間: 2006-5-30 15:45

原帖由 Ivan 於 2006-5-30 15:38 發表
My GTB 5.5 run like a 540. I don't know why, I confirm everything is correct, including the gear ratio. Any bro can help me? Thanks

你set 咗 programme未???

作者: binary 時間: 2006-5-30 15:48

原帖由 Ivan 於 2006-5-30 15:38 發表
My GTB 5.5 run like a 540. I don't know why, I confirm everything is correct, including the gear ratio. Any bro can help me? Thanks

Is your battery malfunctioned? e.g. only 3-4 cells are working, some are just 0 Volts???

作者: Timothypychan 時間: 2006-5-30 15:52
selecting brushless profiles: all LEDs
With ESC on & connected to a charged battery (transmitter ON or OFF):
1. IF TRANSMITTER IS OFF, DISCONNECT ESC FROM RECEIVER
To avoid possible radio interference from other transmitters, remove
the ESC’s input signal harness from the receiver.
2. PRESS & HOLD THE ESC’S ONE-TOUCH SET BUTTON
Continue to hold SET button on ESC until all 4 LEDs turns on.
Note: you will continue holding past the Blue, Blue & Amber, Blue & Green,
and then the Amber LED programming indicators in the ESC’s software.
3. RELEASE SET BUTTON AS SOON AS ALL 4 LEDs COMES ON
Once released, the 4 status LEDs will flash to indicate what Throttle
Profile is currently selected. The number of times the LEDs flash
indicates the Brushless Throttle Profile selection (1 of 5).
4. QUICK PRESS (& release) SET BUTTON TO CHANGE SELECTION
Each press will change to the next consecutive Throttle Profile. (After
Profile 5 in Brushless-Mode, the sequence begins again at Profile 1)
Note: there is a time constraint during this selection process.
5. ESC STORES SELECTION & BEGINS TO EXIT PROGRAMMING
If SET button is not pressed for 3 seconds, ESC stores selected Profile in
memory, exits to neutral & is ready to go. (LEDs turn off in a rolling motion
left to right, until just Red LED is on--Red & Green if no transmitter signal present).
REMEMBER: Whenever One-Touch set-up is performed, ESC automatically reverts to
factory default settings & the Throttle Profile reverts to #1 when in Brushless-Mode.

作者: binary 時間: 2006-5-30 16:11
其實就算乜都唔 set, 只係 set 中位已經 ok 啦喎...... How come it'll as slow as 540.....

作者: Ivan 時間: 2006-5-30 17:04
I also don't know why? Is there any problem about the ESC or motor? I have already changed the bearing. I confirm the condition is good. Any brother can help me?

作者: Timothypychan 時間: 2006-5-30 17:20

原帖由 Ivan 於 2006-5-30 17:04 發表
I also don't know why? Is there any problem about the ESC or motor? I have already changed the bearing. I confirm the condition is good. Any brother can help me?

我自已都係用5.5, 我的經驗就要set 咗 programme 先可以 work.

作者: Timothypychan 時間: 2006-5-30 17:23

原帖由 Ivan 於 2006-5-30 17:04 發表
I also don't know why? Is there any problem about the ESC or motor? I have already changed the bearing. I confirm the condition is good. Any brother can help me?

你現在後波得唔得???

作者: Timothypychan 時間: 2006-5-30 17:24

原帖由 Ivan 於 2006-5-30 17:04 發表
I also don't know why? Is there any problem about the ESC or motor? I have already changed the bearing. I confirm the condition is good. Any brother can help me?

有需要PM電話給我

作者: SunLi 時間: 2006-5-30 17:27

原帖由 Ivan 於 2006-5-30 17:04 發表
I also don't know why? Is there any problem about the ESC or motor? I have already changed the bearing. I confirm the condition is good. Any brother can help me?

If you confirm the conditions of your ESC & motor is good, you may check your radio control system.
As I remember, the first time I use that I need to setup the ESC program before I use to play with it.

歡迎光臨 RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區 (https://rc-evo.com/xbbs/)