RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

標題: question about TLT-1 [打印本頁]

作者: vr2uhu 時間: 2006-6-7 10:36
標題: question about TLT-1
if i use a 2ch remote to control the TLT, but i want 4 wheel steering, is there a thing called servo Y splitter which allow me to use 1 channel controlling 2 servo?
i saw it's jut a simple splitter but dun know if it works.
anyone have tried that plz advice.
thx guys

作者: wave 時間: 2006-6-7 11:10
有D控有mix fuction 唔知得唔得.

作者: Fei 時間: 2006-6-7 13:45

原帖由 vr2uhu 於 2006-6-7 10:36 發表
if i use a 2ch remote to control the TLT, but i want 4 wheel steering, is there a thing called servo Y splitter which allow me to use 1 channel controlling 2 servo?
i saw it's jut a simple splitte ...

係！用一條Y線就可以令兩個Servo，在相同Channel內同時轉動。

作者: vr2uhu 時間: 2006-6-7 14:37
thx pal....
cani get one in KWS? and will it be exp?
if so i will try soldering them together my self
thx

作者: Fei 時間: 2006-6-7 16:22

原帖由 vr2uhu 於 2006-6-7 14:37 發表
thx pal....
cani get one in KWS? and will it be exp?
if so i will try soldering them together my self
thx

Y線廣華街一定有得賣，約幾十蚊一條。

作者: gibson 時間: 2006-6-8 00:07
You may need a mixer, go to the shop next to waigo that sells glider, ask the store keeper, an mixer, you can link two servos together and try try both direction, which one is four wheels turn, with a revers, it will both turn to the same direction.

I used a nine channel transmitter with servors mixing to play with this little TLT before. Check check that shop.

登錄/註冊後可看大圖

作者: gibson 時間: 2006-6-8 00:10
Sorry, if using a mixer, still only can do one stun, either four wheels turn or, both wheels go to the same direction.

I had forgotten already, you may need to try it.

作者: Jackson 時間: 2006-6-8 03:09
Remember to get the reverse Y-harness for proper 4ws. A normal one will give you crabwalking.

作者: vr2uhu 時間: 2006-6-8 09:31
a mixer is just a simple mechanical switch which chnage the red and black wire polariy of the servo or it really consist of some electronic parts? how much will it cost?
u said it will only do one stunt. either 4wheel same direction or 4 wheel turn.
that means i have to reach the car and switch it b4 change the stunt , am i right?
plz advice

作者: vr2uhu 時間: 2006-6-8 09:35
9 CH#_#
i am just thinking about a cheap 4 ch...
but there's a problem that the rignht hand side stick won't auto retract to centre point(whcih is actully for airplanes)
so may be use back a 2 channel instead.

作者: gibson 時間: 2006-6-8 12:40

原帖由 vr2uhu 於 2006-6-8 09:35 發表
9 CH#_#
i am just thinking about a cheap 4 ch...
but there's a problem that the rignht hand side stick won't auto retract to centre point(whcih is actully for airplanes)
so may be use back a 2 c ...

for four channel the right up down is for throttle of a plane, you can ignore it if you are not using this channel.

Check check the manual , I think the manuel will tell you a bit more.

The mixer is a very small device that you can connect two servors in one channel. Will make a photo for you later.

作者: gibson 時間: 2006-6-8 13:04
A mixer is something like this.

登錄/註冊後可看大圖

Photo is my mixer with a lost alarm for glider.

Check the manual I think you may find something, pm me if any further assistance.

作者: simon-c 時間: 2006-6-8 21:12
標題: mix fuction

原帖由 gibson 於 2006-6-8 13:04 發表
A mixer is something like this.

登錄/註冊後可看大圖

Photo is my mixer with a lost alarm for glider.

Check the manual I think you may fin ...

gibson兄，我部TLT 1都有此問題...未解決..，暫用2CH控，可否教我點做你個mix fuction。謝！

作者: gibson 時間: 2006-6-9 02:28
sorry bro I forgot, man when getting old, the memory disappear, if something comes up in my mine, I will update you.

I only remember to use this kind of mixer.

作者: vr2uhu 時間: 2006-6-9 09:11
thx gibson.
done the installation last night,
just DIY solder the servo wire together(cheapestway)

just guess i will seldomly need the (crab walk)
so just forget the mixer
enjoying the 4WS in home last night chasing my cats around...hehe
(it's the 1st 4WS car so far i own...dun laught plz)

作者: vr2uhu 時間: 2006-6-9 09:13

原帖由 Jackson 於 2006-6-8 03:09 發表
Remember to get the reverse Y-harness for proper 4ws. A normal one will give you crabwalking.

i know what u mean but not for TLT///the kit have provide a machanism for normal 4 WS eventhough using normal Y wire
thx anyway

作者: vr2uhu 時間: 2006-6-9 09:21
by the way,....any body know the original servo come with old EX-5 is a meatl gear type or plastic gear type?
i found the servo very noisy when operating....thinking if it's normal or need some lube
the model is something like xx-701 in red words.
any one knows?

作者: gibson 時間: 2006-6-9 12:27

原帖由 vr2uhu 於 2006-6-9 09:11 發表
thx gibson.
done the installation last night,
just DIY solder the servo wire together(cheapestway)

just guess i will seldomly need the (crab walk)
so just forget the mixer
enjoying the 4 ...

Good, enjoy RC with world cup.

Cheers....

作者: HARLEY 時間: 2006-6-9 16:12

原帖由 vr2uhu 於 2006-6-9 09:21 發表
by the way,....any body know the original servo come with old EX-5 is a meatl gear type or plastic gear type?
i found the servo very noisy when operating....thinking if it's normal or need some lu ...

PLASTIC GEAR, 轉起上嚟鬼叫咁.

歡迎光臨 RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區 (https://rc-evo.com/xbbs/)