RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

標題: Slash 4x4 stock motor [打印本頁]

作者: gimsink 時間: 2010-9-26 19:28
標題: Slash 4x4 stock motor
Any ching have a manual for the stock motor for slash 4x4 ? The motor manual in Trax website is difference, it indicate able to remove both end for changing bearing, but the one actually on hand cannot remove the shaft end (pinior gear side). My motor bearing crash today but not able to take iot out for repair...
[attach]416676[/attach][attach]416675[/attach][attach]416674[/attach]

作者: [email protected] 時間: 2010-9-26 19:33
啲啤令散晒

作者: dannychan 時間: 2010-9-26 20:38
試試把整個摩打心放入冰格雪2-3小時，之後一邊旋轉一邊用火機燒個啤令心（注意盡量不要燒到摩打軸）燒到咁上下用鉗把啤令心拔出來。
希望幫到你，但不擔保必定得。

作者: ThomasZ 時間: 2010-9-26 21:25
電波好似有此摩打修護套裝買,印象中大約一百蚊。
但此摩打好像不及teampower的3700kv540好,teampower那隻540省電很多

作者: truckman 時間: 2010-9-26 21:35
回復 4# ThomasZ

終於有c hing 勁過u.......你最多死gear

作者: kiev 時間: 2010-9-26 22:15
磨機''飛"一下就甩 ... 或用鑽石銼慢慢銼 ... 但如果你無工具就買個新摩打算了 ... 呢個可能係玩水戰既代價 ...

作者: gimsink 時間: 2010-9-26 22:42

電波好似有此摩打修護套裝買,印象中大約一百蚊。
但此摩打好像不及teampower的3700kv540好,teampower那隻5 ...
ThomasZ 發表於 2010-9-26 21:25

登錄/註冊後可看大圖

ching, 修護套裝 is not necessary, just change the bearing is enough ( HK$20 maximum ), but the question is not able to take the damaged bearing out, the inner bearing ring is on the shaft, the outer bearing ring is in the motor housing. Manual and Trax website indicate the motor has screw on both end and can take off both end cap for changing bearing, but actually the motor has no screw on shaft end and I cannot take the bearing off the case....I wonder if there is difference version of tye stock motor ??

Team Power's 540 water proof or not ??

作者: gimsink 時間: 2010-9-26 22:43
[attach]416743[/attach]

作者: ThomasZ 時間: 2010-9-27 01:24
回復 7# gimsink

我都唔知防唔防水, 但聽人講所有摩打(除了有感)都防水

作者: tatame 時間: 2010-9-27 10:30
爆bearing 通常都係咁既情況!我novak HV 同TRX motor 爆過5-6次!! 支rotor 用鉗夾實個bearing 圈狠心小小大力挫就整到出黎!!

motor 蓋就煩d ! 要兩個人一人一支一批+槌仔! 平衡地交差式一下一下同時打bearing 圈既兩邊整佢出來

唔洗放棄motor 同rotor !! 因為咩motor 爆bearing 都係咁食住, 買返d 優質bearing 就ok !

作者: ThomasZ 時間: 2010-9-27 14:57
回復 10# tatame

米師兄請問有無試過用4x4套無刷放落架e-maxx到夠唔夠力推?

作者: tatame 時間: 2010-9-27 17:35
本帖最後由 tatame 於 2010-9-27 17:36 編輯

回復 tatame

米師兄請問有無試過用4x4套無刷放落架e-maxx到夠唔夠力推?
ThomasZ 發表於 2010-9-27 14:57

登錄/註冊後可看大圖

540 應該唔夠力~~ 一係用Vtwins ! 玩兩隻XD ~ 不過用一隻550 /600 好過la !

登錄/註冊後可看大圖

http://www.youtube.com/watch?v=cJWWBCgAOio

作者: ThomasZ 時間: 2010-9-27 21:19
回復 12# tatame

我架係summit, 應該用唔到vtwins?
請問550/600 有咩好推介?

作者: gimsink 時間: 2010-9-28 14:27

爆bearing 通常都係咁既情況!我novak HV 同TRX motor 爆過5-6次!! 支rotor 用鉗夾實個bearing 圈狠心小小大 ...
tatame 發表於 2010-9-27 10:30

登錄/註冊後可看大圖

米師兄, thank you for your advise. Ofcourse I will not give up my motor, otherwsie I just buy one and no need to ask all ching's help. Will try as what you said.
Also, the stock motor is longer than normal BL ( around 56mm vs 46mm ), so is it not powerful enough when i install a standard 540 size BL motor to 4x4 ?

作者: gimsink 時間: 2010-9-28 14:44
Also, I reconized that there are some BL motor on sale in RCmart, prices are good, just around US$50 :
Speedpassion V2 11.5T
LRP vector X11 4.5T
Are these motor OK to use with Slash 4x4 ?
If Ok then I want to buy one as backup ....

作者: 導雷斯 時間: 2010-9-28 15:15

回復 tatame

我架係summit, 應該用唔到vtwins?
請問550/600 有咩好推介?
ThomasZ 發表於 2010-9-27 21:19

登錄/註冊後可看大圖

hobbywing 150a 有感

歡迎光臨 RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區 (https://rc-evo.com/xbbs/)