RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

標題: 想玩蛇的朋友,看後會否要再考慮呢 ? [打印本頁]

作者: abcde 時間: 2010-11-7 19:37
標題: 想玩蛇的朋友,看後會否要再考慮呢 ?
今天在jv拍的....那師兄只是和一大腳輕微碰撞後.....
以為rim會比較大損傷...點知.......

作者: Brian086 時間: 2010-11-7 19:43
唔明....

作者: abcde 時間: 2010-11-7 19:59
尾hub灣了.....

作者: RC881 時間: 2010-11-7 20:11

今天在jv拍的....那師兄只是和一大腳輕微碰撞後.....
以為rim會比較大損傷...點知.......
abcde 發表於 2010-11-7 07:37 PM

登錄/註冊後可看大圖

C兄哩部係唔係Pro Ten黎架 ? 輕微碰撞就咁傷真係唔好彩!

作者: Q太郎 時間: 2010-11-7 20:20
食正嘜都頂唔順既

作者: abcde 時間: 2010-11-7 20:22
部車是坐我隔離的12仔蛇.....
佢初玩後驅..巳玩得比較小心的了..見佢和大腳微微撞了一下..以為只是尾rim灣了..點知尾hub都灣埋.....蛇的金屬料無理由咁架....我聽人講asso 野巳經無以前咁好....點解連蛇都咁.....

作者: abcde 時間: 2010-11-7 20:25

食正嘜都頂唔順既
Q太郎發表於 2010-11-7 20:20

登錄/註冊後可看大圖

咁右係....

作者: yeeha0518 時間: 2010-11-7 21:05
so hurt~~~~~~~~

作者: tekin708 時間: 2010-11-7 21:57
impossible... this is too weak...

作者: winclearly 時間: 2010-11-7 22:21

部車是坐我隔離的12仔蛇.....
佢初玩後驅..巳玩得比較小心的了..見佢和大腳微微撞了一下..以為只是尾rim灣 ...
abcde 發表於 2010-11-7 20:22

登錄/註冊後可看大圖

ching,我玩960-07蛇,d萬向系Hudy做,膠料系荷蘭做,
但自960-08開始,所有平地蛇d零件(buggy例外)己經轉了X球,在大陸廠做,所以d質量很差,d960-08蛇,新車d啤呤己不順,油缸漏气(包括733),膠料很弱,d質量差但價錢和x-ray差不多,所以我己冇玩蛇了

作者: hardmankam 時間: 2010-11-8 13:12
That's too bad.

There are so many cars in JV; touring, monster, slash, buggy, 1/12, M, FF with different levels. If there are many cars on the track, I usually stop @ pit and wait until there are less cars.

作者: jf813 時間: 2010-11-9 09:38

ching,我玩960-07蛇,d萬向系Hudy做,膠料系荷蘭做,
但自960-08開始,所有平地蛇d零件(buggy例外)己經轉了 ...
winclearly 發表於 2010-11-7 22:21

登錄/註冊後可看大圖

agree. Their quality used to be very good...... my friends s120 have same issue. And the center thread for the main shaft pull out only after few runs......

作者: airyu 時間: 2010-11-9 09:57
haa.. it seems no good quality 12 son now. still any good quality 12son out there? Xray?

作者: abcde 時間: 2010-11-9 10:09

haa.. it seems no good quality 12 son now. still any good quality 12son out there? Xray?
airyu 發表於 2010-11-9 09:57

登錄/註冊後可看大圖

have buy back that parts (right hub) ?

作者: IS520 時間: 2010-11-9 10:52
哩"post"真係,

你玩 "蛇"; "蛇"玩你.
咁講, "蛇 proten pancar" 又點呢？

作者: airyu 時間: 2010-11-9 11:10
回復 14# abcde

i have ordered la, if world model have stock,, i should get in today..

作者: EG4MAN 時間: 2010-11-9 11:16
好明顯,質料差左好多....

作者: gkl 時間: 2010-11-9 11:19
Everything is made in China now!! SAD!

作者: rsx 時間: 2010-11-9 11:49
Made in china is not the problem, it's the quality control.
It is obvious that the alloy is low grade.

作者: sai20092001 時間: 2010-11-9 12:03
宜家d野咁化學架咩...

作者: fyin 時間: 2010-11-9 13:21
可能用既鋁料已經唔係7075, 改咗啲低guide既鋁料做.
因7075現在真的好貴, 好多模型廠商都冇可能用得起或者都唔會用. (成本高+損耗大)
就算用啲產品出街價都好貴.
我向廣東道都係找到最高檔都係6061.

作者: fyin 時間: 2010-11-9 13:24
已前啲貴零件如果用7075就一定有註明.
現在已好少會標明佢用乜野料做就知喇.

作者: jf813 時間: 2010-11-9 13:26
x-ray samething...... To be hornest CRC seems to be better. I play R5 and my friends runs CRC, serpent, r5.1, x-ray, yokomo.... Only the CRC and r5 do not have much issue. Even the 5.1 seems to be weaker than the r5.....

作者: billgate803 時間: 2010-11-9 14:09
要玩靚料12仔~ 一定要玩MADE IN USA/ MADE IN JAPAN
RC12L3啦~

作者: mkevin 時間: 2010-11-14 00:18
回復 10# winclearly

So dead snake

作者: doraemon 時間: 2010-11-14 16:27
難道所有新車都是軟皮蛇?!!!!

歡迎光臨 RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區 (https://rc-evo.com/xbbs/)