標題: Tpm electronic speed controller [打印本頁] 作者: bear_cat_x 時間: 2012-6-16 12:43 標題: Tpm electronic speed controller Is the Esc still available in the market?作者: wlc 時間: 2012-6-16 12:50
好似仲有TPM8,有錯請指正作者: tiger1 時間: 2012-6-16 14:27
I think there is 作者: bear_cat_x 時間: 2012-6-16 15:05
Thank you Ching. Where can i buy tpm8?作者: BUNNYYUEN 時間: 2012-6-16 15:18 本帖最後由 BUNNYYUEN 於 2012-6-16 15:19 編輯
because I used Tpm2 since 20 years ago, then I used tpm3, and 5. Other than tpm2, they are not damaged easily: I used trinity 52000 rpm motor. I support this hk products just because it is not bad. Why we have to buy substantially more expensive but slightly (maybe) better foreign products? 作者: bear_cat_x 時間: 2012-6-17 02:58
that's why I said "other tan tpm2". 52000rpm trinity motors are the pink ones bought from ct hobbiy作者: bear_cat_x 時間: 2012-6-17 03:01 回復 BUNNYYUEN 的帖子
Thank you作者: kingsleo 時間: 2012-6-17 03:51
support hk products 作者: minimini 時間: 2012-6-17 06:32
the rpm quoted by Trinity was a bit tricky.....they actually using 12V to get the data......while all other brands were using 7.2V ....... 作者: bear_cat_x 時間: 2012-6-17 07:33 回復 minimini 的帖子
really? But it made my lazer very fast.作者: minimini 時間: 2012-6-17 08:43
during that era........Reedy modified (hand-winded 14T) usually had ~ 28000 to 32000rpm at 7.2V (as quoted by the factory).......
while Trinity started to release some sort of hand-winded 11T, 12T motors...... plus 12V as the testing voltage.....which pushed them up to 52000rpm.......of course if they were all using 7.2V...... 12T Trinity should still be faster than 14T Reedy....... 作者: tiger1 時間: 2012-6-17 09:00
TP quality is actually not bad but QC sometime is a problem. Good that you can get them fixed in HK easily. Cheap too 作者: BUNNYYUEN 時間: 2012-6-17 10:33
絕對支持香港產品,大家記吾記得大約10几年前有架1:10叫seven 都系香港人設計,另外以前在灣仔橋底場附近有間叫星星模型有個車仔設計賣咗比日本仔之后就發咗吾使點做,而得寶的售后服務亦相當滿意,就算你個電變BBQ都好,頂多味收你一舊,仲要你飲個茶轉頭攞,ok嫁作者: bear_cat_x 時間: 2012-6-17 15:10 回復 BUNNYYUEN 的帖子
Where is tak po now?作者: BUNNYYUEN 時間: 2012-6-17 15:54
系深水埗高登商場對面好似系福仁商場一樓作者: bear_cat_x 時間: 2012-6-17 16:18 回復 BUNNYYUEN 的帖子
Thank you Ching. It seems that tak po is still at the same location as 20 years ago.作者: BUNNYYUEN 時間: 2012-6-18 03:13
應該系冇變過作者: tiger1 時間: 2012-6-19 17:48
售后服務滿意 then is really good作者: bear_cat_x 時間: 2012-6-19 21:29 回復 BUNNYYUEN 的帖子
Are you still using tpm?作者: BUNNYYUEN 時間: 2012-6-20 09:05
有乜問題??作者: Andrew168 時間: 2012-6-20 11:05
已經冇用佢產品好耐, 但都支持德寶, 可靠, 售後服務好, 價格合理作者: bear_cat_x 時間: 2012-6-20 11:54 回復 Andrew168 的帖子
I have no idea regarding their after-sale service ar, because I have not brought stuffs to them for repairing作者: bear_cat_x 時間: 2012-7-2 02:45
tak po is still here and I have just bought a tpm8