RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

標題: Toe in/out 的設定? [打印本頁]

作者: wai    時間: 2006-10-31 18:57
標題: Toe in/out 的設定?
前輩,前輩,其實車頭設定toe in定係toe out會好彎D?

設定toe in/out應該相差幾多mm先好喇?

請詳盡解釋設定原理 / \  \ /.   


作者: sunnyshao007    時間: 2006-11-2 11:43
TOE IN:smaller of the turning
TOE OUT:bigger of the turning
PS:but the other setting is important too!!!

作者: rsx    時間: 2006-11-2 13:08
usually, toe out會好彎D  (but toe out will decrease straight line stability)
作者: c230    時間: 2006-11-2 13:35
原帖由 rsx 於 2006-11-2 13:08 發表
usually, toe out會好彎D  (but toe out will decrease straight line stability)



甘系尾 SET 番少少 TOE IN 又補唔補夠到呢?
作者: justinwan    時間: 2006-11-2 14:02
係depens on  你個彎大小,   

影響你入彎, 彎心, 出彎速度 ......   如果你set toeout  入彎會比較慢, 流暢d , 無咁死  .
仲要配合埋個camber .

所以無話咩好彎吾好彎, 睇場地, and 自己風格
作者: rsx    時間: 2006-11-2 15:12
Well, it depends on too many factors (track, car, driver, other chassis setup ... ... ...).

Usually, if you use front toe out, you'll also dial in some rear toe in (or dial in larger camber angle, ... etc) to compensate.  It's all about compromise.

To have a true answer, you'll need to try it out on the track with a lap counter and experiment on different setting.  (Although I never try this myself )

原帖由 c230 於 2006-11-2 13:35 發表



甘系尾 SET 番少少 TOE IN 又補唔補夠到呢?  

作者: wai    時間: 2006-11-2 18:38
重有..重有..FW O5R 跑街用頭單向定齒义好彎喇?

...........................唔該晒.......................

                   
作者: benz1850    時間: 2006-11-2 19:32
For front oneway, I set to 0 degree. if not, 1 to 2 degree toe out, for better corning.  Correct me if I am wrong...thanks in advance.
作者: cowcowlee    時間: 2006-11-2 20:48
原帖由 wai 於 2006-11-2 18:38 發表
重有..重有..FW O5R 跑街用頭單向定齒义好彎喇?

...........................唔該晒.......................

                   



咁就要視乎塊地咬唔咬, 咬地嘅話用單向比較好, 反之用牙义, 如果唔係出彎時車尾會好nut...好難救, 不過最緊要都係自己鐘意....
P.S. 我都係玩05R...
作者: wai    時間: 2006-11-2 21:18
咁我又想問吓,頭單向唔係加油時行直塞嘅咩,唔係

應該帶住份頭出彎嘅咩,唔明?唔明?
作者: cowcowlee    時間: 2006-11-2 22:25
http://www.rc-evo.com/m_newhand/hand030.html
可以望下呢度...

再唔係就罷架車落地試下啦....
作者: smp    時間: 2006-11-3 11:11
原帖由 wai 於 2006-11-2 21:18 發表
咁我又想問吓,頭單向唔係?br />
應該帶住份頭出彎嘅咩,唔明?唔明?

當然不是,落頭直軸就有這效果.




歡迎光臨 RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區 (https://rc-evo.com/xbbs/) Powered by Discuz! X3.2