RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區
標題: Xray T1, T2, T3, T4 Parts Stocked! [打印本頁]
作者: Dinballian 時間: 2012-12-18 17:29
標題: Xray T1, T2, T3, T4 Parts Stocked!
本帖最後由 Dinballian 於 2012-12-18 17:49 編輯
Xray Front Suspension Arm (One Hole) – Graphite for T2 T3 T4 #XR-302167
Molded lightweight composite front lower suspension arm. The specially-formulated graphite composite material allows for a very light suspension arm that can withstand the rigors of high-performance racing. Fits XRAY T2, T3 cars.
The optimized suspension arm gives improved traction, easier handling, and decreases tire overheating which leads to car stoppage under high-grip conditions. Features a single optimized shock mounting position and integrated anti-roll bar mounts. The graphite arm has same size and geometry as standard 1-hole suspension arm.
Item no.:XR-302167
Xray Graphite Chassis 2.2mm #XR-301134
The new 2.2mm thick chassis is CNC-machined from premium-grade graphite material and provides maximum traction under low traction conditions while maintaining stability and forgiveness under high traction conditions. Specifically designed for LiPo batteries, all electronics are located along the centerline to make this the best-balanced electric touring car.
The high-grade, custom-manufactured carbon graphite is specially produced based on XRAY’s own recipe and specifications.
Item no.:XR-301134
Xray Composite Ball Joint 5mm Short Open for T2 T3 T4 #XR-303454
Molded composite 4.9mm ball joints for anti-roll bar links, same as included in anti-roll bar sets #302401 (front) and #303401 (rear).
Item no.:XR-303454
Xray Composite Anti-Roll Bar Holders for T2 T3 T4 #XR-303411
Molded composite anti-roll bar holders, same as included in anti-roll bar sets #302401 (front) and #303401 (rear). Set of 8.
Item no.:XR-303411
Xray Composite Upright 0 degree Outboard Toe-In – Medium – Rubber Spec for T2 T3 T4 #XR-303352
Molded-composite rear upright features built-in 0° of outboard toe to improve traction and prevent suspension geometry changes in serious crashes. Features two roll center positions on the top of the rear upright. Accommodates small but robust 5×10 ball-bearings for minimized unsprung weight.
Medium rigidity (labeled "M") specially optimized for rubber-tire racing.
Use on both left and right sides of the car. Can be also used for foam tires.
Item no.:XR-303352
Xray Composite Rear Suspension Arm (One Hole) – Graphite for T2 T3 T4 #XR-303167
Molded lightweight composite rear lower suspension arm. The specially-formulated graphite composite material allows for a very light yet suspension arm that can withstand the rigors of high-performance racing. Fits XRAY T2, T3 cars.
The optimized suspension arm gives improved traction, easier handling, and decreases tire overheating which leads to car stoppage under high-grip conditions. Features a single optimized shock mounting position and integrated anti-roll bar mounts.
The graphite arm has same size and geometry as standard 1-hole suspension arm.
Item no.:XR-303167
Xray Composite C-Hub Right 4 degree – Hard – Foam Spec for T2 T3 T4 #XR-302373
Molded composite C-hub for right steering block of T2, T3. Caster pre-set at 4°. Hard rigidity for foam-tire racing. Use with matching left-side C-hub #302374. Can be also used for rubber tires.
New C-hub has large openings for quicker & easier assembly/disassembly of CVDs. The entire CVD assembly can be easily inserted/removed through the C-hub without the need for disassembly, and the large openings prevent binding of the CVD in serious crashes.
The C-hubs are available in all standard caster angles (2°, 4° and 6°) and are also available in two different rigidities that are optimized for particular racing conditions. The EU Edition includes medium rigidity (M) C-hubs specially optimized for rubber-tire racing, while the US Edition includes hard rigidity (H) C-hubs specially optimized for foam-tire racing.
Item no.: XR-302373
Xray Composite Dual Servo Saver Arm for T3 T4 #XR-302526
This is a molded arms for dual servo saver, made form tough composite material. Suitable for left and right arms.
Item no.: XR-302526
Xray Ball-Bearing Composite Bushing for T2 T3 T4 #XR-302295
Item no.:XR-302295
Xray Composite Shock Ball Joint – Open for T2 T3 T4 #XR-308316
Item no.:XR-308316
作者: Dinballian 時間: 2012-12-18 17:32
本帖最後由 Dinballian 於 2012-12-18 17:56 編輯
Xray Composite Spur Gear 114T / 64P for T1 T2 T3 T4 #XR-305884
XRAY precision molded spur gear. This spur gear has been strategically lightened to reduce rotating mass.
Item no.: XR-305884
Xray Composite Spur Gear 112T / 64P for T1 T2 T3 #XR-305882
Item no.: XR-305882
Xray Composite Spur Gear 84T / 48P – Hard for T1 T2 T3 T4 #XR-305784
Item no.:XR-305784
Xray Composite Offset Spur Gear 108T / 64P for T1 T2 T3 #XR-305878
Item no.: XR-305878
Xray Composite Offset Spur Gear 110T / 64P for T1 T2 T3 #XR-305880
Item no.: XR-305880
Xray Composite Offset Spur Gear 104T / 64P for T1 T2 T3 #XR-305874
Item no.: XR-305874
Xray Anti-Roll Bar Rear 1.2mm for T4 #XR-303492
Item no.:XR-303492
Xray Anti-Roll Bar Front 1.6mm for T4 #XR-302496
Item no.:XR-302496
Xray Anti-Roll Bar Front 1.2mm for T4 #XR-302492
This is a replacement XRAY 1.2mm Front Anti-Roll Bar, and is intended for use with the XRAY T4 1/10 scale electric touring car. This is the stock front anti-roll bar.
Item no.:XR-302492
Xray Anti-Roll Bar Front 1.4mm for T4 #XR-302494
Item no.: XR-302494
Xray Anti-Roll Bar Front 1.5mm for T4 #XR-302495
Item no.: XR-302495
Xray Ball Universal 5.8mm Hex #XR-303241
Ball 5.8mm with hex cavity, for connection to molded composite ball joints. Set of four.
Item no.:XR-303241
Xray 007 Ball End 5mm with Thread for T2 T3 T4 #XR-302652
Item no.:XR-302652
Xray 4S Spring Set C =2.5 for T4 #XR-308275
Item no.: XR-308275
Xray 4S Spring Set Progressive C = 2.5-2.8 for T4 #XR-308264
Item no.: XR-308264
Xray 4S Spring Set C =2.3 for T4 #XR-308274
Item no.: XR-308274
| 歡迎光臨 RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區 (https://rc-evo.com/xbbs/) |
Powered by Discuz! X3.2 |
