RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

標題: carbon lipo AE86 [打印本頁]

作者: billy86che 時間: 2007-1-10 22:46
標題: carbon lipo AE86
a recent DIY

作者: terencelyl7411 時間: 2007-1-10 22:47
你係 CT 個 Billy !?

作者: 清清 時間: 2007-1-10 22:53

原帖由 billy86che 於 2007-1-10 22:46 發表
carbon lipo AE86
a recent DIY

何以見得是AE86？謝~

作者: ALEXANDER 時間: 2007-1-10 22:56

原帖由清清於 10/1/2007 10:53 PM 發表

何以見得是AE86？謝~

果條鈴係~

作者: billy86che 時間: 2007-1-10 22:57
another photo

作者: kaho0338 時間: 2007-1-10 22:58
只係覺得今既mod.....好似1:10 touring 車架

不過lipo 可以玩到幾耐呢?

作者: billy86che 時間: 2007-1-10 22:59
標題: 回復 #6 kaho0338 的帖子
I am using 500 mah batt and a 60 turn motor. the car can run about 10 mins.

作者: kaho0338 時間: 2007-1-10 23:01

原帖由 billy86che 於 2007-1-10 22:59 發表
I am using 500 mah batt and a 60 turn motor. the car can run about 10 mins.

會唔會比普通電爆?

作者: billy86che 時間: 2007-1-10 23:03
DIY collection

作者: billy86che 時間: 2007-1-10 23:04
Diy car 3 & 4

作者: billy86che 時間: 2007-1-10 23:05

原帖由 kaho0338 於 2007-1-10 23:01 發表

會唔會比普通電爆?

Yes. It is 7.4 V on average and 8.4 V when fully charged.

作者: billy86che 時間: 2007-1-10 23:12

原帖由清清於 2007-1-10 22:53 發表

何以見得是AE86？謝~

see this

作者: 清清 時間: 2007-1-10 23:19

原帖由 billy86che 於 2007-1-10 23:12 發表

see this

THANK YOU

作者: billy86che 時間: 2007-1-10 23:29
all are lipo.

作者: checkie 時間: 2007-1-11 03:44
老師果然利害~

作者: 嘈喧巴閉 時間: 2007-1-12 18:56

原帖由 checkie 於 2007-1-11 03:44 發表
老師果然利害~

老師加工程師

作者: terencelyl7411 時間: 2007-1-14 19:38
睇下 billy 魔打上面粒電容大到！？

作者: billy86che 時間: 2007-1-15 12:15

原帖由 terencelyl7411 於 2007-1-14 19:38 發表
睇下 billy 魔打上面粒電容大到！？

How big? Which one? I guess I use only normal type.

作者: rk2 時間: 2007-1-15 12:26
do you have all the DIY steps ( with photos), I think you have done a very good DIY job.

作者: billy86che 時間: 2007-1-15 13:34

原帖由 rk2 於 2007-1-15 12:26 發表
do you have all the DIY steps ( with photos), I think you have done a very good DIY job.

I have steps on making the carbon enzo and making the rear damper of the subaru but not with this one. You can refer to previous posts.

Try the following:
http://rc-one.com/phpwind/read.php?tid=2229&fpage=7
http://rc-one.com/phpwind/read.php?tid=2595&fpage=6

[ 本帖最後由 billy86che 於 2007-1-15 13:46 編輯 ]

作者: terencelyl7411 時間: 2007-1-15 15:11

原帖由 billy86che 於 2007-1-15 12:15 PM 發表

How big? Which one? I guess I use only normal type.

14th floor , the left one

作者: billy86che 時間: 2007-1-15 16:16

原帖由 terencelyl7411 於 2007-1-15 15:11 發表

14th floor , the left one

唔明, please explain

作者: terencelyl7411 時間: 2007-1-15 16:20

原帖由 billy86che 於 2007-1-15 04:16 PM 發表

唔明, please explain

十四樓，最左邊果架

作者: billy86che 時間: 2007-1-15 17:48

原帖由 terencelyl7411 於 2007-1-15 16:20 發表

十四樓，最左邊果架

你講嘢真係好簡潔.
有冇相?

[ 本帖最後由 billy86che 於 2007-1-15 18:00 編輯 ]

作者: terencelyl7411 時間: 2007-1-15 18:03

原帖由 billy86che 於 2007-1-15 05:48 PM 發表

你講嘢真係好簡潔.
有冇相?

登錄/註冊後可看大圖

最左果架

作者: billy86che 時間: 2007-1-15 20:30

原帖由 terencelyl7411 於 2007-1-14 19:38 發表
睇下 billy 魔打上面粒電容大到！？

They are normal motor capacitors. See this picture.

作者: KamSing 時間: 2007-1-15 20:43

原帖由 billy86che 於 2007-1-15 20:30 發表

They are normal motor capacitors. See this picture.

Yes, he used mono caps which are different from the common ones( c caps).

作者: terencelyl7411 時間: 2007-1-15 20:45

原帖由 billy86che 於 2007-1-15 08:30 PM 發表

They are normal motor capacitors. See this picture.

O ，我以為魔打開孔果度係粒電容系 tim

作者: billy86che 時間: 2007-1-15 20:47

原帖由 KamSing 於 2007-1-15 20:43 發表

Yes, he used mono caps which are different from the common ones( c caps).

They are just a little more expensive. You can buy dozens of them at a very low price in Ap Liu Street

作者: 韓哥 時間: 2007-1-19 17:34

原帖由 billy86che 於 2007-1-10 23:04 發表
Diy car 3 & 4

個粉紅色摩打座係?

作者: billy86che 時間: 2007-1-19 21:17

原帖由韓哥於 2007-1-19 17:34 發表

個粉紅色摩打座係?

It is similar to this:
(a shortened motor mount from GxM)

作者: bob488884 時間: 2007-1-28 16:35
can you po more pic?

我广州嘅……5该5该……

作者: billy86che 時間: 2007-1-29 13:24
I'm glad to. See if tonight I'm free.

作者: bob488884 時間: 2007-1-29 17:05
thx!

作者: billy86che 時間: 2007-1-29 19:00
servo is from futaba (3110)

作者: billy86che 時間: 2007-1-29 19:02
modified gear so I can fit wider rear tyres (up to 14mm)

作者: billy86che 時間: 2007-1-29 19:05
The running weight is less than 160 grams so I added 10 grams to lower the CG at that time when I took the photo. I now have 15 extra grams on the bottom, making the car weighing about 170 grams in total.

作者: billy86che 時間: 2007-1-29 19:06
I added caster to the front.

作者: billy86che 時間: 2007-1-29 19:07
some camber to the front so I don't need to buy camber front carrier. In fact, they are not the same in nature.

作者: billy86che 時間: 2007-1-29 19:09
the lipo battery cells are laid down as shown to achieve the lowest CG possible.

作者: billy86che 時間: 2007-1-29 19:10
Compare the older MR02 86 and the new 86. I hope by doing this, I can run the 86 shell faster (compensating the height of the body shell).

[ 本帖最後由 billy86che 於 2007-1-29 19:12 編輯 ]

作者: billy86che 時間: 2007-1-29 19:14
The rear motor mount is modified from GxM product. It was originally 98mm. Now it becomes 90mm.

作者: billy86che 時間: 2007-1-29 19:15
Top view of the old and the new 90mm 86.

作者: billy86che 時間: 2007-1-29 19:16
A closer top view.

作者: bob488884 時間: 2007-1-29 22:09
wow,thx! I'm trying to make a 1/24……but the motor mount is a problem……

作者: billy86che 時間: 2007-1-29 22:34
標題: 回復 #45 bob488884 的帖子
There should be longer H bar on the market to help you make a 1/24. Of course you might have to use the 98mm motor mount.

作者: billy86che 時間: 2007-2-5 19:26
Recent move:

I added more lead to the bottom (169 grams running weight with shell). Pic 2

I now use 14mm rear tyres (left). Compare them with 11mm tyres (right). Pic 1

作者: LANCIA 時間: 2007-2-6 09:43
痴系车底果D系咩黎架？

作者: billy86che 時間: 2007-2-6 13:01

原帖由 LANCIA 於 2007-2-6 09:43 發表
痴系车底果D系咩黎架？

鉛

作者: 韓哥 時間: 2007-2-6 18:50

原帖由 billy86che 於 2007-2-6 13:01 發表

鉛

幾多g?

作者: billy86che 時間: 2007-2-6 20:56
about 10 grams

歡迎光臨 RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區 (https://rc-evo.com/xbbs/)