RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

標題: ESC setting for F1 [打印本頁]

作者: hsukoonyuen 時間: 2014-11-24 13:20
標題: ESC setting for F1
hello i am playing F1 in JV, can u share your setting of your F1 so that beginner can use it as build reference?

chassis type
car width, narrow or wide
ride height
tyre type
motor turn
gear ratio
esc punch
esc drag brake
esc timing / turbo
esc brake force
battery type

作者: WagwanBumba 時間: 2014-11-24 13:55
Hey - have only started playing F1 but I've found not a lot of information out there. Short answer is, because there's no specific class types at JV, it's all run what you brung (bad english) and as long as you're most comfortable with it.

I'm using 13.5T with 32.5 timing on the endbell and 0 timing on the ESC. 63 spur and 31 pinion. Not sure if this is right cos I've not managed to do a run for long enough to guage motor temps to see if it's under/over geared but seemed ok. This was comfortable speed for me but with a bit of head room for more speed if I want it.

90% of the setup is in the tyres! I tried Ride R1 and I couldn't get enough steering because I couldn't get the front tyres warm enough. Other chings using modified motors saying that rubber tyres just aren't going to hack it for F1, especially because I go in the evenings and the surface temperature is colder now. Just bought some GQ Racing front and rear foams! They looked really good on the track last week. They have them in Action Hobbies. I have VBC LightningF and you must get to F104 wheels for this car; the front wheels are fouled by the king pin on the front if you get the F103.

1 step at a time! Get the foams on and get the car on the track and have fun

Then change things 1 by 1.

Also found out that for pan cars, diff should be set relatively loose! This could also be why I was having difficulty with understeer.

作者: samuel20461 時間: 2014-11-24 13:59
Play wide and use foam tyres. Motor 17.5r add turbo.Easy drive at JV.

作者: hsukoonyuen 時間: 2014-11-24 19:07
Thats exactly what I am using in JV, but the car slip or spin when turbo is on...

作者: nel3838 時間: 2014-11-24 20:13
本帖最後由 nel3838 於 2014-11-26 10:25 編輯

hsukoonyuen 發表於 2014-11-24 19:07
Thats exactly what I am using in JV, but the car slip or spin when turbo is on...

F1 is like a giant 1/12 and there are lots of setup tips on web for 1/12. 17..5 with turbo perhaps too much if new to F1, and wears sponge tyres quickly at JV.

作者: feihome1 時間: 2014-11-25 08:43
Any speed of motor you prefer to play at JV?

作者: nel3838 時間: 2014-11-25 10:23
本帖最後由 nel3838 於 2014-11-26 10:26 編輯

feihome1 發表於 2014-11-25 08:43
Any speed of motor you prefer to play at JV?

Fei Hing, play with you, anything motor is fun laa....

. Right now, probably prefer 21.5 (with or without Turbo) due to current race rules.

作者: ricksonchow 時間: 2014-11-25 12:43

WagwanBumba 發表於 2014-11-24 13:55
Hey - have only started playing F1 but I've found not a lot of information out there. Short answer i ...

For the Ride R tyre, I have the same issue as you. Front tire aren't really grippy but the rear is okey. However the rear tyre are easily un-glued even I use the stock silver can 540 brushed motor. So may be I'd better stick with sponge tyres.

作者: hsukoonyuen 時間: 2014-11-25 17:29
can u recommend a cost effective foam tyre? it seens the cheapest is 200hkd a set, and only last for 5 packs before i need to replace the rear tyre

作者: feihome1 時間: 2014-11-25 21:39

nel3838 發表於 2014-11-25 10:23
Fei Hing, play with you, anything motor is fun laa.... . Right now, probably prefer 21.5 (with ...

Do I need to set the exceeded gear ratio if I use the 21.5t？

作者: nel3838 時間: 2014-11-25 22:11
本帖最後由 nel3838 於 2014-11-25 22:14 編輯

feihome1 發表於 2014-11-25 21:39
Do I need to set the exceeded gear ratio if I use the 21.5t？

without turbo, yes. becomes like 540 white can settings.

作者: ICY 時間: 2014-11-29 02:07
本帖最後由 ICY 於 2014-11-29 02:09 編輯

個人認為窄陣車一定係玩膠，棉個樣我頂唔順

歡迎光臨 RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區 (https://rc-evo.com/xbbs/)