RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

標題: 越野四驅BUGGY用乜SERVO好? [打印本頁]

作者: AMAT 時間: 2007-6-6 18:22
標題: 越野四驅BUGGY用乜SERVO好?
扭力?速度?邊樣行先?我宜家手頭就得O的3003.....諗緊買唔買一隻新FOR架未來DF03用.....

作者: TOMY(HONG) 時間: 2007-6-6 18:38
大力ge,唔洗太快

作者: mikewu 時間: 2007-6-6 18:41
9550 law... but I use 9451 for mine....

作者: AMAT 時間: 2007-6-6 18:43

原帖由 mikewu 於 2007-6-6 18:41 發表
9550 law... but I use 9451 for mine....

9550仲貴過9451喎大哥.......

作者: leeho888 時間: 2007-6-6 18:45
3003 ok la~~

作者: AMAT 時間: 2007-6-6 18:47

原帖由 leeho888 於 2007-6-6 18:45 發表
3003 ok la~~

3003真係又呆又冇力......冇錢惡講.......

呢排有幾個臭錢係身.....想用好小小嗎~

作者: mikewu 時間: 2007-6-6 18:48

原帖由 AMAT 於 2007-6-6 18:43 發表

9550仲貴過9451喎大哥.......

We use 9550 for 1:8s... but honestly, I think 9451 is good enough..... (very good actually)....

作者: ftbingobingo 時間: 2007-6-6 18:51
Futaba S9351, Hi-Tec 5955

作者: gibson 時間: 2007-6-6 20:22

原帖由 AMAT 於 2007-6-6 18:43 發表

9550仲貴過9451喎大哥.......

I think 9451 over 500, 9550 less than 500...

作者: crusaderlyf 時間: 2007-6-6 20:22
SANWA WRX 0.06s/8kg,够快又好力

作者: AMAT 時間: 2007-6-6 20:56
好.....攞車時再諗下~

作者: ryancmlam 時間: 2007-6-6 22:30

原帖由 AMAT 於 2007-6-6 18:47 發表

3003真係又呆又冇力......冇錢惡講.......
呢排有幾個臭錢係身.....想用好小小嗎~

3003 cost only $60. Very cost effective.

作者: bigben 時間: 2007-6-7 00:05
i am using 3003..... ok la.

my skill can compensate the weakness of my df03....

[ 本帖最後由 bigben 於 2007-6-7 00:06 編輯 ]

作者: minimini 時間: 2007-6-7 00:07
I am using KO 2000 servo (7.2V servo)........with metal gears...... really nice.....

作者: Panda 時間: 2007-6-7 00:20
Futaba New 9452 la ..................
0.11 s 9Kg/cm

作者: i-Drift 時間: 2007-6-7 09:28
I think Hitec's servos are good for buggy. More torque.

作者: vr2xvh 時間: 2007-6-7 14:04
我擺左隻bluebird 616mg落去, 聲稱有 9.6kg-cm 0.12s, 星期五試下用唔用得

作者: RCman 時間: 2007-6-7 14:23

原帖由 vr2xvh 於 2007-6-7 14:04 發表

 登錄/註冊後可看大圖

我擺左隻bluebird 616mg落去, 聲稱有 9.6kg-cm 0.12s, 星期五試下用唔用得

我用過一個Bluebird
覺得佢好吳得，Case易難，Gear易掃！
我不會再買Bluebird servo

剛剛買左兩Hitec Servo, 625MG
$264一個
兩個都裝落buggy上，DF03, RB5

FEATURES: Three metal gears
      Metal/plastic 1st gear
      Dual ball bearing
      Designed for R/C helicopters, boats, and glow or electric cars.

SPECS: Speed:  0.18sec/60? at 4.8V
               0.15sec/60? at 6.0V
      Torque: 5.5 kg-cm (76.37 oz-in) at 4.8V
               6.8 kg-cm (94.43 oz-in) at 6.0V

作者: kawada 時間: 2007-6-7 14:24
One question Bro Boss.. u are talking about EP or GP buggy ?? infact, i dont really recommend 9550, since its a low profile servo with pretty low torgue which cannot handle buggy torgue eating requirements.. I would suggest those with metal gears with at least 8kg output torgue for EP buggies ( just my opinion ) if u r talking about GP buggies.. required alot more than that

Look at its spec ..

Dimension  40.5 mm x 21 mm x 25.4 mm
Weight  45 g
Operating Speed  0.11 sec/60°
Output torque  6 kg-cm

[ 本帖最後由 kawada 於 2007-6-7 14:31 編輯 ]

作者: kawada 時間: 2007-6-7 14:30
S9451  Digital servo

Coreless motor, 6.0V only
Dimension  40.0 mm x 20.0 mm x 36.6 mm
Weight  56 g
Operating Speed  0.10 sec/60°
Output torque  8.7 kg-cm

S3003  Analog servo

4.8V or 6.0V
Dimension  40.4 mm x 19.8 mm x 36.0 mm
Weight  37.2 g
Operating Speed  0.23 sec/60° (4.8V)
0.19 sec/60° (6.0V)
Output torque  3.2 kg-cm (4.8V)
4.1 kg-cm (6.0V)

作者: 師傅東 時間: 2007-6-7 15:59
3003玩吓就冇乜所謂

9550出嚟唔係o甘用哩！

9451啱啱好嘞！

作者: dl7 時間: 2007-6-7 17:31
9451 how much?

作者: gibson 時間: 2007-6-7 17:36

原帖由 dl7 於 2007-6-7 17:31 發表

 登錄/註冊後可看大圖

9451 how much?

Around HKD550.

作者: buggy 時間: 2007-6-7 18:01

原帖由 gibson 於 2007-6-6 20:22 發表

 登錄/註冊後可看大圖

I think 9451 over 500, 9550 less than 500...

9550 is 498hkd only...

歡迎光臨 RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區 (https://rc-evo.com/xbbs/)