RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

標題: 離合器問題!! [打印本頁]

作者: jimcarry    時間: 2007-7-25 00:40
標題: 離合器問題!!
有彈弓加三塊甩塊既 clutch.

而家要加到好高速架車先move, 比小小油一D反應都無,應該要點較呢,用左好多介子啦。
我想知正常onroad 1/10油車,係咪一比油就會行家?

Thanks a lot!!
作者: 泉    時間: 2007-7-25 01:03
如果是推槳式, 嘗試將彈弓鬆一點了
作者: chrishkyung    時間: 2007-7-25 09:15
maybe your oneway bearing has problem at the main shaft
作者: sunnyshao007    時間: 2007-7-25 09:44
標題: 回復 #3 chrishkyung 的帖子
關咩事呀~!!!
佢係試親次次都係咁~
我問過佢,我認定係條極力力彈弓有事~!!!
條彈弓太緊,導致要俾多d油個極力子先可以彈出去頂住個含鐘~!
只要用枝一字pipe係條彈弓與彈弓之間界一界就得(開闊條彈弓,減少彈弓既回壓力)
試下啦~!!!(唔得就換條較鬆既彈弓)
作者: chrishkyung    時間: 2007-7-25 17:55
標題: 回復 #4 sunnyshao007 的帖子
High hand Sunnyshao

I just share my experience....no need to condemn ah....

BTW, as told by jimcarry, "要加到好高速架車先move, 比小小油一D反應都無,應該要點較呢,用左好多介子啦。"  From my experience, everyone facing the similar problem.  They will try to adjust the clutch spring for 推槳 at the first moment.  Of course, I dont know what the clutch he is using.  But as long as he is playing on road GP with 2 speed.  The car will 要加到好高速架車先move if its one way bearing has problem.  

I am talking about the one way bearing installed in the first gear not the front one way diff....

High hand....If i am wrong, u ar welcome to correct me....

BTW, what car and clutch brother jimcarry ar using? If u can post the photo, maybe people can help to find out the problem...
作者: BHP    時間: 2007-7-25 18:10
If his problem was already known,
he wouldn't have to post this thread.

Sunny, your analysis might not be the cause.
And even if it is, what's the need for this harsh language?
We're here to share experience and help others (and get ourselves poisoned =P)

------------

A stupid question here,
but are the brakes absolutely "off" when you apply throttle?
Since you didn't mention this in your thread,
are the brakes applied when you apply throttle?
Does your car roll freely?

[ 本帖最後由 BHP 於 2007-7-25 18:16 編輯 ]
作者: jimcarry    時間: 2007-7-25 19:29
標題: 回復 #6 BHP 的帖子
尋日同 sunny 講講下我斷左線,所以未到結論@@ ``
因為我睇左好多 clutch 既發動原理,但係又奇怪點解原廠個 setting 會咁。

我想知正常既 1/10 nitor car 加小小油 就行 or 要再加多 D 先行?
如果係加小小就行,我覺得就係 Sunny 講既彈弓太硬。 低速離合器啟動唔到。

如果係咁重有咩方法解決呢?謝謝
作者: DieselEngine    時間: 2007-7-25 19:36
原帖由 jimcarry 於 25/7/2007 07:29 PM 發表
尋日同 sunny 講講下我斷左線,所以未到結論@@ ``
因為我睇左好多 clutch 既發動原理,但係又奇怪點解原廠個 setting 會咁。

我想知正常既 1/10 nitor car 加小小油 就行 or 要再加多 D 先行?
如果係加小 ...

我想知正常既 1/10 nitor car 加小小油 就行 or 要再加多 D 先行?
任你SET, 鬆BRAKE就自己溜前都得.
作者: chrishkyung    時間: 2007-7-25 19:49
first, u need to check if u push throttle, if your engine gear rotate....

if it rotate, the problem is likely at the one way bearing of the first gear

if not rotate, its the problem of your clutch...

please let us know which engine and clutch u ar using....then help u to solve the problem...if can, please post photo
作者: 倒錢落海    時間: 2007-7-25 20:10
原帖由 DieselEngine 於 2007-7-25 19:36 發表:任你SET, 鬆BRAKE就自己溜前都得.
搭訕:唔知係咪我副野set得唔好,初初撻著部車,就咁擺係度佢係唔會行,俾少少油就行,收油唔落brake就會逐漸停,但當玩左一陣,副野熱熱地,咁就算唔俾油,部車都會慢慢溜前,要落住brake部車先會停。呢個現象是否正常?

[ 本帖最後由 倒錢落海 於 2007-7-25 20:13 編輯 ]
作者: DieselEngine    時間: 2007-7-25 20:16
原帖由 倒錢落海 於 25/7/2007 08:10 PM 發表
搭訕:唔知係咪我副野set得唔好,初初撻著部車,就咁擺係度佢係唔會行,俾少少油就行,收油唔落brake就會逐漸停,但當玩左一陣,副野熱熱地,咁就算唔俾油,部車都會慢慢溜前,要落住brake部車先會停。呢個現象 ...

呢個現象正常. 副機熱左就會高轉d.
你玩FW05?
作者: lokaman    時間: 2007-7-25 20:31
原帖由 chrishkyung 於 2007-7-25 17:55 發表
High hand Sunnyshao

I just share my experience....no need to condemn ah....

BTW, as told by jimcarry, "要加到好高速架車先move, 比小小油一D反應都無,應該要點較呢,用左好多介子啦。"  From my  ...


作者: 倒錢落海    時間: 2007-7-25 20:41
原帖由 DieselEngine 於 2007-7-25 20:16 發表:呢個現象正常. 副機熱左就會高轉d.你玩FW05?
係呀05t+...^^~。多謝指點。
作者: sunnyshao007    時間: 2007-7-26 00:56
標題: 回復 #5 chrishkyung 的帖子
如果粒bearing死左,
every time 俾油既深度會好唔同!!!
但係佢差唔多次次都係同樣既rpm架車先識行
chris,佢唔係用推掌,
佢只係用三塊個d fing手掌
個d離合器既驅動方式,
如果條彈弓較得唔好,
好似jim個d問題就會較推掌更易顯露~!!!(只係我既feeling)
作者: DieselEngine    時間: 2007-7-26 02:39
原帖由 倒錢落海 於 25/7/2007 08:41 PM 發表
係呀05t+...^^~。多謝指點。

如果唔想咁, 換過條硬身既彈弓, 同埋睇下你條彈弓有冇斷到.
作者: kwok    時間: 2007-7-26 14:09
油車唔係電車呀!夠轉數個離合器才會打開的.
作者: 倒錢落海    時間: 2007-7-26 15:02
原帖由 DieselEngine 於 2007-7-26 02:39 發表:如果唔想咁, 換過條硬身既彈弓, 同埋睇下你條彈弓有冇斷到.
唔該晒^^           




歡迎光臨 RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區 (https://rc-evo.com/xbbs/) Powered by Discuz! X3.2