RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

標題: 油車"皮帶車"點計齒比呢. [打印本頁]

作者: pskyng 時間: 2008-3-26 19:29
標題: 油車"皮帶車"點計齒比呢.
想請問.
電車一般會有個基數比你計個齒比.(e.g T2 係 spur/pinion x 1.7=R ), 想問油車"皮帶車" 點計的(因為1,2波,又有3組pulley..). ..若以NT1為例. 是否要加埋所有pulley 來計個"final gear ratio" 個基數是否由offical 比 or 有得計的.?

thanks r.

[ 本帖最後由 pskyng 於 2008-3-26 19:32 編輯 ]

作者: SunLi 時間: 2008-3-26 20:16
XRAY NT1 Set-up Book (page. 37)

http://www.teamxray.com/teamxray ... ;catName=XRAY%20NT1

作者: justinwan 時間: 2008-3-26 20:35
i tell u , it is useless...because your tires is being smaller and smaller. its only work for rubber tires.

and y u need to know the gear ratio ? it only few clutch bell gear thats u can install .

作者: Oakfield 時間: 2008-3-26 20:42

原帖由 SunLi 於 2008-3-26 20:16 發表

 登錄/註冊後可看大圖

XRAY NT1 Set-up Book (page. 37)
http://www.teamxray.com/teamxray ... ;catName=XRAY%20NT1

How about MTX ar. Mr. Bean

作者: SunLi 時間: 2008-3-26 20:49

原帖由 Oakfield 於 2008-3-26 20:42 發表

 登錄/註冊後可看大圖

How about MTX ar. Mr. Bean

Here you go!!

http://www.mugenseiki.com/mtx4-overdriveratio.pdf
http://www.mugenseiki.com/mtx4-rollout.pdf

作者: Oakfield 時間: 2008-3-26 21:05

原帖由 SunLi 於 2008-3-26 20:49 發表

 登錄/註冊後可看大圖

Here you go!!
http://www.mugenseiki.com/mtx4-overdriveratio.pdf
http://www.mugenseiki.com/mtx4-rollout.pdf

Very good; thanks Brother Bean:@ :@ :@

作者: taky 時間: 2008-3-26 23:10

原帖由 SunLi 於 2008-3-26 20:49 發表

 登錄/註冊後可看大圖

Here you go!!
http://www.mugenseiki.com/mtx4-overdriveratio.pdf
http://www.mugenseiki.com/mtx4-rollout.pdf

how anout 3r????
thx

作者: pskyng 時間: 2008-3-27 15:10
thanks all bro useful information.

I just wanna know more about nitro car basic theory and for reference from some technique quiz like this post that I can't get any ans from web search.

as G4s, K-factory's "ED system" change the car "final ratio" to reduce engine loading and improve power transfer .and, my car just around 1st 18/52 ,2nd 24/47, I watch others car like NT1 spur gear up to 58..so, it blast me ask "gear ratio"

歡迎光臨 RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區 (https://rc-evo.com/xbbs/)