RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

標題: What da! [打印本頁]

作者: mikewu 時間: 2006-4-12 14:34
標題: What da!
WA! What the hell is this..... what a ugly truck.....

http://cgi.ebay.co.uk/TAMIYA-KNI ... QrdZ1QQcmdZViewItem

作者: hc1309 時間: 2006-4-12 15:06

作者: 胖胖熊 時間: 2006-4-12 16:57

原帖由 mikewu 於 2006-4-12 14:34 發表
WA! What the hell is this..... what a ugly truck.....

what a ugly truck.....

作者: buppalo 時間: 2006-4-12 19:56
點解你成很日用英文？出於好奇摟主唔好介意

作者: PRiNCe 時間: 2006-4-12 20:26
425 UKP = $5767 HKD

it is FWD too

作者: tommy1218 時間: 2006-4-12 22:32
就咁將個油缸裝上去，整體本人覺得太長，好似格硬左Ｄ！應該ｃｕｔ短少少！

作者: Eddie 時間: 2006-4-12 23:00

原帖由 buppalo 於 2006-4-12 19:56 發表
點解你成很日用英文？出於好奇摟主唔好介意

有問題咩 ?

呢部野好型呀 ~!
(k果隻)唔知係咪真有其車。

作者: ricksonchow 時間: 2006-4-12 23:06

原帖由 PRiNCe 於 2006-4-12 20:26 發表
425 UKP = $5767 HKD

it is FWD too

really fwd? how could u see that?
咁長~ 轉向半徑.........

作者: PRiNCe 時間: 2006-4-12 23:15

原帖由 ricksonchow 於 2006-4-12 16:06 發表

really fwd? how could u see that?
咁長~ 轉向半徑.........

it looks like a direct drive to the front

if not the dog bone/drive shaft will have to be custom to be long enough to reach the back wheels

咁長~ 轉向半徑 - I think it could turn on the spot if it was FWD

back wheels grip and the front wheels grip

作者: buppalo 時間: 2006-4-12 23:16

原帖由 Eddie 於 2006-4-12 23:00 發表

有問題咩 ?

呢部野好型呀 ~!
(k果隻)唔知係咪真有其車。

沒問題，只是好奇一問樓主是西人還是中國

作者: ricksonchow 時間: 2006-4-13 02:32

原帖由 PRiNCe 於 2006-4-12 23:15 發表

it looks like a direct drive to the front if not the dog bone/drive shaft will have to be custom to be long enough to reach the back wheels

咁長~ 轉向半徑 - I think it could turn on the ...

ICIC~ 第一次見fwd truck~ 咁佢都好多野搞wor~ 因為以星星貨車頭擔,波箱同front wheel既設計,整fwd都不容易

作者: J 時間: 2006-4-13 04:25
don't think it's FWD as it says it includes "extended prop."

作者: PRiNCe 時間: 2006-4-13 06:27

原帖由 J 於 2006-4-12 21:25 發表
don't think it's FWD as it says it includes "extended prop."

hmm there is a possibility but the lenght of the prop must be at least 300mm

that will snap amost instantly when put into pressure...and the drive must be so wierd unless all of the rear 4 axles turn. and if you have a look at the hole behind the motor you can't see a prop through the hole

hmmm somebody e-mail him to find out

作者: J 時間: 2006-4-13 06:31
right, I can't see any prop sticking out but it might be due to the unfinished project nature. does that make sense to you?

作者: PRiNCe 時間: 2006-4-13 06:50

原帖由 J 於 2006-4-12 23:31 發表
right, I can't see any prop sticking out but it might be due to the unfinished project nature. does that make sense to you?

hmm yes i think your right as i don't have much knowledge of the knight hauler's drive design

sorry for misleading ricksonchow

作者: mikewu 時間: 2006-4-13 10:32

原帖由 buppalo 於 2006-4-12 19:56 發表
點解你成很日用英文？出於好奇摟主唔好介意

Sorry, I am Chinese and I speak Chinese.. But I don't know how to write much as my Chinese skills are only at F.4 level...........

It's ok that you ask.....

作者: HF3648 時間: 2006-4-13 20:08
非與本文章有關的討論市請另開新文章討論

歡迎光臨 RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區 (https://rc-evo.com/xbbs/)