HOBBYWING 好盈電子變速器玩家專區：

請問punch有2段，punch個度數係代表甚麼呢？同boost既進角有冇關係！會否影響全段turbo進角總和thx!

有無師兄試過V10 4.5T如何呢? thx

小弟用lrp x20 stock10.5,請問可否用modified模式？及如果modified和stock10.5模式設定數值—樣，車子速度是否也一樣？小弟怎樣設定也不及别人x20 10.5快。小弟玩417，齒比7.3，大減113,麽打齒30，boost40,turbo28.請指点—下小弟，謝謝

電池，差机也有関係……
我想問stock v3.1 同modify v3.1 用來玩10.5T 其實有沒有分別？
我意思指電變本身stock果隻平幾百元，如果不玩modify.是否買stock就可以？

trf415msx 發表於 2013-11-5 02:02
電池，差机也有関係……
我想問stock v3.1 同modify v3.1 用來玩10.5T 其實有沒有分別？
我意思指電變本身s ...

我想問其實modify,stock有咩分别？

請問我用緊120a v2.1, 一開個電變就閃綠燈，請問咩signal?

綠島滌野 發表於 2013-11-22 11:51
請問我用緊120a v2.1, 一開個電變就閃綠燈，請問咩signal?

你可先查一下sensor線 的連接是否正常. 如果連接正常, 再試下換馬達Sensor版再試一下.

請問2.1外殼可訂嗎？要怎樣訂?

請問V3用blinky mode有沒有不同program,因為在加拿大比賽要用blinky mode。有沒有blinky mode專用的program呢？

你 set Zero Timing mode 就係啦!!
點 set 睇返說明書最尾嗰頁啦!
http://www.hobbywing.com/uploadfiles/sx/file/Manual/HW-SM510CHN.pdf

salton 發表於 2013-7-24 10:05
V2.1 120A目前来看仍然是性价比超高的选择。

外观，体积，可调教的参数更多，更多的辅助功能是V3.1的优 ...

師兄，請教HW 2.1 esc Lrp x20 4.5
玩Jv 怎樣set 電變各項
齒比（84/19）乘 （38/19）= 8.8
麻煩哂

本人玩zero s , 齒輪 比= (80/31) x (38/19)=5.16. 用 hw 120a + hw 10.5 T 有感motor.
排電 7.4 v 2 cell 30C full charge, 玩到每cell 3.5v左右, 電變勁閃 red 燈不能動, 要等一會或off 開關 然後on 番. 先可以行約30sec, 然後出現 同一情況red 燈勁閃不能動.
想問一下是
1)gear ratio 不對所至( 但手試過 motor 不是很熱)
2) battery c 數不夠.
3) 電熔 壞了.
4)還是esc setting problem
煩請 c hing 教一下
thanks

wolf 發表於 2014-1-2 17:40
本人玩zero s , 齒輪 比= (80/31) x (38/19)=5.16. 用 hw 120a + hw 10.5 T 有感motor.
排電 7.4 v 2 cell  ...

Gear ratio 好似低左啲，. Battery 30c ? 低！50 c la

thx c hing, 但motor 都不太熱, 及想知 esc 勁閃 red 燈係也意思呢? 會否玩壞了?因arm arm 重玩 rc .請教一吓

因為esc可能set 低電壓 自動停

ericwu 發表於 2014-1-2 20:17
因為esc可能set 低電壓 自動停

已玩回20 motor 齒 及 only set esc at 3.2v cut off. 但都在 full charge 7.2 v 2 cell 30 c 後, 到每cell 3.5v 左右, 個esc 閃red 燈. 冇反應!! please help

Ching,
Just my own case for your reference.
I have 5 HW ESC actively being used - V2.1(60, 90 and 120A) and Ezrun x 2.
I have to turn off 低電壓 protection for all 5 ESCs to get rid of the situation you descrbe above.
By doing so, you have to make sure you play within a reasonable time in order not to get your Lipo over discharged. What is a reasonable time depends on your electronics combination and FDR. Try and measure - this will need to be done quite a few times. Happy trying.

tsfai 發表於 2014-1-3 17:42
Ching,
Just my own case for your reference.
I have 5 HW ESC actively being used - V2.1(60, 90 and  ...

thx a lot ching information. according to your case about hobby wing esc, it means the low voltage cut off fuction is useless. we need to monitor the voltage by the old fashion way. between c hing would you suggest me a better esc other than hobbywing esc?

wolf 發表於 2014-1-4 04:10
thx a lot ching information. according to your case about hobby wing esc, it means the low voltage ...

Ching, forgot to mention that I have to turn off temp protection as well to enable continuous play.In my case I can play around 10 mins with below:
Zero s FDR 8.0
motor 7.5T with T+B = 60
6000mah 60c lipo
Motor and ESC temp less than 40c in Decemeber.
In your case, I guess you better get a lipo at least with 40c or above.
Just personal idea for your reference.
I think HW is a good value for money product.