改裝一問！

請問各位師兄師傅如果想玩AWD有D乜野一定要改先行得好呢？
買一部齋車好定係買一部ready to run好呢？

謝謝！

齋車~唔係行得嫁咩=.="????

原帖由 kelvinblstz 於 2007-3-12 21:22 發表
齋車~唔係行得嫁咩=.="????

kws有一set係齋車包啤零，但唔包控同車殼$880

原帖由 chingwingtat 於 2007-3-12 21:21 發表
請問各位師兄師傅如果想玩AWD有D乜野一定要改先行得好呢？
買一部齋車好定係買一部ready to run好呢？

謝謝！

一定要換呔..!!!

我想買車時一次過連必需改裝配件一齊買，所以想要張清單。

如果玩dirft就一定要換呔,同埋啤令都一定要

視乎你玩快車定飄移
我覺得如果你有心玩就買散件會好D因為唔會浪費D原裝料

Kyosho centre drive shaft (Heavy duty)
Kyosho MZ8-3 Mini-Z Stock Servo Gear Shaft
Atmoic servo gear set
Kyosho MD010 Mini-Z AWD Stock PCB or Buy KO Propo AD PCB
3Racing or Atomic Mini-Z AWD Aluminum Front Tie Rod -1° Toe Out
PNRacing AWD Aluminum Motor Gear 17 Tooth
PNRacing Motor Heat Sink
3Racing motor holder (A2B2)
PNRacing AWD Spring Set
3Racing Kunckle 1 degree front and 2 degree rear
3Racing dog bone
Bearing set
3Racing rims lock nut
Rims offset depend on your shell
Shell (recommend Audi wide shell, Fairlady GT, NSX GT, R34 GT, CLK GTR)
Tires Fast (front 20 degree slick, rear 10 degree with pattern)
Futaba 2PL if you use AM PCB
KO EX-10 with AD module if you want to use AD

唔該晒[email=tonytjia@zone]tonytjia@zone[/email]tonytjia@zone[/email]兄 ！

原帖由 tonytjia@zone 於 2007-3-13 02:10 發表
視乎你玩快車定飄移
我覺得如果你有心玩就買散件會好D因為唔會浪費D原裝料

Kyosho centre drive shaft (Heavy duty)
Kyosho MZ8-3 Mini-Z Stock Servo Gear Shaft
Atmoic servo gear set
Kyosho MD010 Min ...

如果玩dirft 用SAS 好定係用哂金屬波箱好?

原帖由 tonytjia@zone 於 2007-3-13 02:10 發表
視乎你玩快車定飄移
我覺得如果你有心玩就買散件會好D因為唔會浪費D原裝料

Kyosho centre drive shaft (Heavy duty)
Kyosho MZ8-3 Mini-Z Stock Servo Gear Shaft
Atmoic servo gear set
Kyosho MD010 Min ...

About how much for this config.? Thanks!  (exclude the transimitter price and using AM PCB)

淨係一個AM PCB 邊到有得賣同埋幾錢左右ga

我向極x模型見過AM PCB $250

未用過SAS但D師兄話要set得好有排試

呢set野係我最近砌的
大約千幾
Kyosho Gery/Blue Chassis $130
Kyosho centre drive shaft (Heavy duty) $70
Kyosho MZ8-3 Mini-Z Stock Servo Gear Shaft 唔記得
Atmoic servo gear set 唔記得
KO Propo AD PCB Set with Module & Band $700
3Racing or Atomic Mini-Z AWD Aluminum Front Tie Rod -1° Toe Out $30
PNRacing AWD Aluminum Motor Gear 17 Tooth $30
PNRacing Motor Heat Sink $150
3Racing motor holder (A2B2) $40
PNRacing AWD Spring Set $50
3Racing Kunckle 1 degree front and 2 degree rear $100
3Racing dog bone $90
Bearing set $80
3Racing rims lock nut $25
Rims offset depend on your shell
Shell (recommend Audi wide shell, Fairlady GT, NSX GT, R34 GT, CLK GTR)
Tires Fast (front 20 degree slick, rear 10 degree with pattern)
Futaba 2PL if you use AM PCB $230
KO EX-10 with AD module if you want to use AD

原帖由 tonytjia@zone 於 2007-3-13 16:03 發表
呢set野係我最近砌的
大約千幾
Kyosho Gery/Blue Chassis $130
Kyosho centre drive shaft (Heavy duty) $70
Kyosho MZ8-3 Mini-Z Stock Servo Gear Shaft 唔記得
Atmoic servo gear set 唔記得
KO Propo A ...

ad pcb 如果就咁買會大約幾錢呀TONY

around 1.7k with no shells

我有控，只係想買部車試下玩下，唔駛太專業，所以睇下邊D parts係必需要改的！

原帖由 tonytjia@zone 於 2007-3-13 22:49 發表
around 1.7k with no shells

你個setting 係for dirft 定係快車ga?

I found these the "must-change parts" for a fast car:

pinion gears
metal motor plates
1.5 front and rear hubs
full bearings
PN shortest springs for AWD
tyres
a fast motor
fets installed
Kyosho ball differentials (F & R)
shims for lowering the chassis

Stick the 2 gears on the centre shaft using instant glue so you don't have to buy the metal one. I found other things not essential.

I think centre shaft is a must buy stuff for fast car as the gear will wear out with high speed motor.

Motor gear & Motor heat sink is a must buy item as well. I prefer PN one.