FF02

Any C-hing still playing FF02.
Let Share photo.

登錄/註冊後可看大圖

Pls share.

Pls share.
agentjerry 發表於 2010-9-5 09:49

                               
登錄/註冊後可看大圖

    你架唔係FF01咩?

舊車, M03改FF02, 已出售...

舊車, M03改FF02, 已出售...
move7648 發表於 2010-9-5 10:13

                               
登錄/註冊後可看大圖

move7648兄,M03既轉向杯同尾hub用吾用得番呢?我買左加長件,A臂同頭C座,其它未買,萬向有無得淨系買長狗骨用番原本既萬向呢?

回復 5# nastyboy

M03既轉向杯同尾hub用吾用得番呢? <== yes

萬向有無得淨系買長狗骨用番原本既萬向呢? <== lee個就唔知, sorry

THX.................

Pls share.
agentjerry 發表於 2010-9-5 09:49

                               
登錄/註冊後可看大圖

    哇,出光花

回復 5# nastyboy

萬向有無得淨系買長狗骨用番原本既萬向呢?  - yes, buy the 39mm one.

in accordance with my experience, the length of the FF02 is a bit shorten, not 257mm, it is ranging from 252 to 257 depends on the front toe out.

On the other hand, the width of FF02 is around 5mm less then today's car such as TA05, FF03.

回復  nastyboy

萬向有無得淨系買長狗骨用番原本既萬向呢?  - yes, buy the 39mm one.

in accordanc ...
ryancmlam 發表於 2010-9-5 22:32

                               
登錄/註冊後可看大圖

Thx a lot,仲想問下,咁臂pin要買邊款呢?我朋友剛剛去買TL01臂用既pin,他對一對長好多,系咪又要買第二款車既臂pin呢?或就咁用厚介子就呢?

Thx a lot,仲想問下,咁臂pin要買邊款呢?我朋友剛剛去買TL01臂用既pin,他對一對長好多,系咪又要買第二款 ...
nastyboy 發表於 2010-9-6 11:48

                               
登錄/註冊後可看大圖

are you using the TL01 arms, if yes, TL01臂用既pins are fine.
If you are using the TL01LA arms, you can still use the body-end pins but the wheel-end pins. If I remember correctly, the wheel-pins are TA04 ones

回復 1# SamsonSung

My FF02,
ESC: LRP ICS,
Motor: Blk Pig,
Servo: 9650,

Thanks All !!

so nice!!!

回復 14# longman0072

Last time I tried it in TRC, the handling is quite good. However, the downstop cannot be controlled directly like FF03. So, some o-rings have been placed inside the dampers to control the downstop.

Thanks All !!

回復 1# SamsonSung

ching o既廠花?  靚!!

回復  longman0072

Last time I tried it in TRC, the handling is quite good. However, the downstop ...
yokomo 發表於 2010-9-6 17:38

                               
登錄/註冊後可看大圖

yes, there is no down stop setting screw in the TL01/ M03 / FF02 series. we need a lot of time to disassemble the damper and put/remove o-ring inside for setting the down stop