FF02 - RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

作者: ryancmlam 時間: 2010-9-5 22:32
回復 5# nastyboy

萬向有無得淨系買長狗骨用番原本既萬向呢? - yes, buy the 39mm one.

in accordance with my experience, the length of the FF02 is a bit shorten, not 257mm, it is ranging from 252 to 257 depends on the front toe out.

On the other hand, the width of FF02 is around 5mm less then today's car such as TA05, FF03.

作者: nastyboy 時間: 2010-9-6 11:48

回復 nastyboy

萬向有無得淨系買長狗骨用番原本既萬向呢? - yes, buy the 39mm one.

in accordanc ...
ryancmlam 發表於 2010-9-5 22:32

登錄/註冊後可看大圖

Thx a lot,仲想問下,咁臂pin要買邊款呢?我朋友剛剛去買TL01臂用既pin,他對一對長好多,系咪又要買第二款車既臂pin呢?或就咁用厚介子就呢?

作者: ryancmlam 時間: 2010-9-6 12:03

Thx a lot,仲想問下,咁臂pin要買邊款呢?我朋友剛剛去買TL01臂用既pin,他對一對長好多,系咪又要買第二款 ...
nastyboy 發表於 2010-9-6 11:48

登錄/註冊後可看大圖

are you using the TL01 arms, if yes, TL01臂用既pins are fine.
If you are using the TL01LA arms, you can still use the body-end pins but the wheel-end pins. If I remember correctly, the wheel-pins are TA04 ones

作者: yokomo 時間: 2010-9-6 13:24
回復 1# SamsonSung

My FF02,
ESC: LRP ICS,
Motor: Blk Pig,
Servo: 9650,

Thanks All !!

: 登錄/註冊後可看大圖

: 登錄/註冊後可看大圖

: 登錄/註冊後可看大圖

作者: longman0072 時間: 2010-9-6 16:07
so nice!!!

作者: yokomo 時間: 2010-9-6 17:38
本帖最後由 yokomo 於 2010-9-6 17:45 編輯

回復 14# longman0072

Last time I tried it in TRC, the handling is quite good. However, the downstop cannot be controlled directly like FF03. So, some o-rings have been placed inside the dampers to control the downstop.

Thanks All !!

作者: 1524 時間: 2010-9-8 23:37
回復 1# SamsonSung

ching o既廠花? 靚!!

作者: ryancmlam 時間: 2010-9-8 23:44

回復 longman0072

Last time I tried it in TRC, the handling is quite good. However, the downstop ...
yokomo 發表於 2010-9-6 17:38

登錄/註冊後可看大圖

yes, there is no down stop setting screw in the TL01/ M03 / FF02 series. we need a lot of time to disassemble the damper and put/remove o-ring inside for setting the down stop

歡迎光臨 RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區 (https://rc-evo.com/xbbs/)