team power7.5T 磨打set turbo

想問下個setting大概點樣
有冇D例子可以參考
我用SP 120A電變
thanks

回復 20# 870110a


Ching,

Do you have the option LCD program card. GT2.0 pro, prostock 2.1 and GT2.0 LPF should able to use firmware 100528MOD. It is the firmware for modified motor (low turn down to 3.5R) and provide super charge option and setting!

回復 21# snipertat

師兄，你好勇阿！

回復  snipertat


    吾怕燒野咩?.?
870110a 發表於 2010-10-6 12:17

                               
登錄/註冊後可看大圖

    唔怕..因為只係錢既問題.可以解決
但玩左30排電..未見有事
連過熱 cut電都未試過

回復 21# snipertat


    吾怕燒野咩?.?

用梗咩528mod????
870110a 發表於 2010-10-6 03:18

                               
登錄/註冊後可看大圖

    係528stock

我60A + 8.5T
9 Timing  (7) 18°
12 Turbo Timing  (3) 2°
13 Boost Start RPM  (7) 12000
14 Turbo  ...
snipertat 發表於 2010-10-6 00:41

                               
登錄/註冊後可看大圖

    用梗咩528mod????

回復  snipertat

Ching,

Can you share your gear ratio and which track you are playing on???? S ...
shungyan 發表於 2010-10-6 00:57

                               
登錄/註冊後可看大圖

3R    櫻花ZERO
64P 108/30 X 1.9 = 6.84

回復 17# snipertat

Ching,

Can you share your gear ratio and which track you are playing on???? Super Thx!\

我60A + 8.5T
9 Timing  (7) 18°
12 Turbo Timing  (3) 2°
13 Boost Start RPM  (7) 12000
14 Turbo Delay  (3) 0.1
15 Timing Punch(RPM/ °)  (7) 1000

已經好好表現..拍住D 5.5T玩無問題
不過玩完一排電都幾熱下
要休息下先可以再黎

咪玩啦^^
lionpp 發表於 2010-10-5 20:09

                               
登錄/註冊後可看大圖

信唔信除你

set Turbo "max"
IBM 發表於 2010-10-5 13:53

                               
登錄/註冊後可看大圖

咪玩啦^^

set Turbo "max"  

now 7.1925

what is the internal ration??
shungyan 發表於 2010-10-4 23:16

                               
登錄/註冊後可看大圖

減速齒左右果2個就係18T
頭尾都係37T

what is the internal ration??

SP 120A can support modified motor as low as 3.5T with turbo (However, with such low turn, turbo is  ...
shungyan 發表於 2010-10-4 22:32

                               
登錄/註冊後可看大圖

另外我想問下我個減速齒係105T，我個磨打就7.5T,磨打齒要用幾多好呢? (我而家用緊30齒)
thanks

SP 120A can support modified motor as low as 3.5T with turbo (However, with such low turn, turbo is meaningless as you cannot boost it too much). You will need

1. Make sure your ESC is prostock or GT2.0
2. download the newest firmware and load the proper firmware into the ESC. It should be 100528mod or 100528stock. Of course you need 100528 for 7.5T.
3. Do not use any advanced timing in your motor's endbell
4. Beware of overheat when setting the turbo (supercharge). 7.5T is not that low in term of modified.
5. Beware of gear ratio. Overgear will burn!
6. Finally, you still need to bear the risk. Suggest you send mail to SP for suggestion. If I were you I will set it from the lowest and monitor the temp and speed one by one.

Ps. I am using the same ESC but not dare to do so. I am using 4.5T. I am looking for cheap 6.5T. Hope that you could share your result afterward.

ok  thanks

回復 5# lionpp


    there is turbo delay!!!