any news of Losi Comp?

fist lot are already delivered in america
any news of release date in KWS?



It starts showing up in the states like this one here ....

http://www.rccrawler.com/forum/s ... &postcount=1353

                               
登錄/註冊後可看大圖

Seems like LCC is geared for faster motor (eg.35T) and 3S Lipo..

Here for your reference
http://www.rccrawler.com/forum/forumdisplay.php?f=181

觀塘買，   
http://www.rcmart.com/catalog/rc ... roller-p-28865.html
我未決定電子野，得一隻12T麼打齒&55T麽打，剛剛做緊setting，發覺有2個缺點，
a) 兩支油壓同時按下按到最盡時，電池架底布帶有少少頂中軸(約3mm)，
b) 單一支油壓按下按到最盡時，不可45度轉向，最多40度左右，因車呔會磨到油壓彈弓&磨到中軸(左邊按下)。
個人覺得，換幼少少metal中軸有需要，我用hot racing 鈴多了約1cm offset無磨到油壓彈弓，但闊咗少少吾靚仔，要等老手們指教，慢爬我都係吾多識。

p.s.條呔真係好得

我都買咗架試玩，2K野 ok，原裝已跟一套囉C批幾實用，好在未買批，servo arm係金屬，
好可惜中軸是膠
simontam 發表於 2009-6-12 20:26

                               
登錄/註冊後可看大圖

噫, 有工具送咁方便? 想問下你架車嚮邊到買?

20# simontam

我架冇囉C批跟..   佢D金屬servo arm 冇配比 Futaba用嘅...而我係用9157..  
C hing 打算用乜野 Motor 同幾多齒呀?

我都買咗架試玩，2K野 ok，原裝已跟一套囉C批幾實用，好在未買批，servo arm係金屬，
好可惜中軸是膠

18# simontam

重未知. 架車我未有時間同工具去拆. 不過CVD個道落鏍絲膠+heat shrink 應該安全掛

13# fly175hk
Thank you U
CVD是否個角度有問題or原裝d鐵料差
？

14# rockdragon


Wow!! Really great tips!! Thank you.

15# 馬田

重有, 全車8成以上用英制鏍絲,好唔方便. 我要買過晒D架生. 另外架車唔跟摩打齒...

架車好正,不過我會睇多排先買, 外國玩家己發現上述問題...
睇下losi 下水貨會唔會改善問題...

10# rockdragon


Thx so much for your advice. Are those Tamiya Grease good enough? Can you elaborate a bit on "how to heat sink tube at all CVD pin"?
I still have no time to put those electronic ...
fly175hk 發表於 2009-6-7 00:36

                               
登錄/註冊後可看大圖

here it is ..... where the pins are and example of what after the heat shrink tube is done.

                               
登錄/註冊後可看大圖

                               
登錄/註冊後可看大圖

11# simontam


我見到佢寫明唔用Dig 就: "If you will not be using the optional DIG system,remove the small tie rod attached to the shift horn" 其實都係好簡單 .

10# rockdragon


Thx so much for your advice. Are those Tamiya Grease good enough? Can you elaborate a bit on "how to heat sink tube at all CVD pin"?
I still have no time to put those electronics in yet

請問如果我吾用DIG可以嗎？要點樣整法？
Thank you

Wowwww ... so good la.

just make sure you take it all apart and check all parts.
When you put it back, do not forget to put a lot of black grease at the worm gears and threadlock all screws.
One very important must do is heat shrink tube at all CVD pins.

do not play it before you do all this, otherwise damage is surely show up shortly.

Just arrived yesterday

                               
登錄/註冊後可看大圖

                               
登錄/註冊後可看大圖

                               
登錄/註冊後可看大圖

唔知香港到時賣幾多錢.. 呢架野我等左好耐...

it is artr?