外國加州會長黃色華Dee之setting(值得參考)

Electronics Used
·         7.2v GP1100mAh NiMH - charge at 1 Amp

·         Hitec HS-81

·         Novak XXL 2-channel FM 75MHz (or smallest one you can find)

·         Deans battery connectors for low resistance

·         Castle Creations Mamba 6800Kv brushless motor

·         Castle Creations Mamba 25A brushless ESC


Modifications

Steering:


·        Kyosho special steering parts (secure w/nylon nut), tighten down until slightly touching

·        Tighten down stock steering head horizontal 2.6mm shaft until there is a small amount of play (easy to swivel), any more will cause binding

·        Adjust trims with rider off first, then add and adjust rider to compensate


Front End:

·         TOPCAD ball bearings (2 wheels)

·         GPM aluminum front discs

·         Silicone front insert hard compound

·        Add 4mm shims in steering head at bottom bearing of triple clamps to remove play

·         Kyosho front oil forks (1 drop each of 40wt. oil or grease, stretched stock springs, thread lock nuts on top)

·         Stock front tire preferred (high grip front tire wider & less pointed)

·         Spin front tire next to your ear and dremel off any friction spots (i.e. inner forks & mudguard)

·         Forks stock length; 8-9mm from top of front axle mounts to bottom of shocks (use calipers)

·         Put plastic washers on top of forks inside triple clamps to lengthen front ride height

·         Attach/remove front calipers on outside to avoid rubbing discs

·         Put thin washers on front axle ends and tighten until friction is reached, then back off


Main Chassis:

·          Epoxy frame at front & rear inner crash bar mounts and gearbox mounts (scratch off chrome first, leave 4-40 screw in before epoxy, dremel left side after for gearbox clearance)

·          Servo tape ESC switch into slot


Rear End:

·         TOPCAD ball bearings (2 wheels)

·         GPM rear disc plates

·         Use high grip or Suzuki rear rim (rear sprocket fits better)

·         1/2" round foam gap sealer rear insert (diagonal cut ends, press fit inside)

·         HPI touring super shock (upside-down), Super RS4 end, piston #5 (plug 2 holes w/CA), 1 large preload spacer, Trinity 60wt. oil, Associated red spring (22 lb.)

·         Kyosho high grip rear tire

·         Shave off right side of swing arm shaft hole to allow swing arm to move up & down freely (a little play)

·         Put thin washers on rear axle ends and tighten down all the way


Drive Train:

·         TOPCAD ball bearings (4 gearbox)

·         GPM/TOPCAD oval washers

·         GPM/TOPCAD alum. gearbox w/2mm hex screws

·         HPI micro steel pinion 13T

·         Kyosho steel gearset (middle gear only)

·         Cut slot into gearbox & drill hole into battery tray for easier pinion service

·         Trinity 3mm Teflon shims in gearbox

·         Chain tension slightly tight


Body:

·         Use 2-56 acetal screws and washers to attach windshield

·         Attach CF strips to bottom fairing to screw onto top cowling

·         Put Team Associated chassis protector tape on bottom fairing to protect from scratches

·         Or. . . don’t use bottom fairing at all!


Rider:

·         Dremel down rear end of Suzuki rider b/c it rubs on back seat attachment

·         Ziptie body halves together

·         Cut g-block joints out of CF plate and close loops to prevent joints from disconnecting


Electronics:

·         Attach foam spacers on rear of battery packs for a snug fit in the battery tray

·         Velcro tape receiver to inner rear tank and trail antenna thru rider


Last updated: 5/17/05



Radio Control Motorcycles Club of California

Ian's Kyosho setup page

[ 本帖最後由 beebee 於 2006-1-3 02:16 AM 編輯 ]

車花好正~

噴到咁靚,邊捨得玩呀!?!哈!

Silicone front insert hard compound...........Still Waiting for it!

抄底D SETTING先
第時可能有用

架車好靚呀
羅絲同卡皮羅絲呀
不過仲係NSR500年代
同樣咁經典呀

係呀!D SETTING可以參考吓,都有用架

原帖由 beebee 於 2006-1-17 23:47 發表
係呀!D SETTING可以參考吓,都有用架

有無得轉返做中文呀
有D睇唔明呀